Unfortunately, again, the number you're calling 4131, is not matching the
dial-peers you posted; however, the debugs are still saying you're hitting
DP 5, which is an H323 DP not SIP.

On Thu, Mar 1, 2018 at 1:44 PM Hamu Ebiso <hebiso2...@hotmail.com> wrote:

>
> Here is the debug output for debug voip ccapi inout, and debug ccsip
> messages.
>
>
> Thank you again for your help.
>
>
>
>
> ------------------------------
> *From:* Anthony Holloway <avholloway+cisco-v...@gmail.com>
> *Sent:* Thursday, March 1, 2018 1:16 PM
> *To:* Hamu Ebiso
>
> *Cc:* Cisco VoIP Group
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
> debug voip ccapi inout, and if you're using SIP, then debug ccsip messages
> as well.  the debug vpm signal is not very helpful, though it does show the
> port selected.
>
> On Thu, Mar 1, 2018 at 1:05 PM Hamu Ebiso <hebiso2...@hotmail.com> wrote:
>
> Thank you Anthony very much for your help.
>
> The 19529473283 <(952)%20947-3283> for  connection plar 19529473283
> <(952)%20947-3283> I was testing with. After changing of few things on
> the gateway, I'm now seeing different messages when I run debug. The calls
> used to ring only one time and then fast busy, now it rings twice and then
> fax busy for incoming. for outgoing, it's says calls connot be completed as
> dialed.
>
>
> Attached the new logs again. I really appreciate your help.
>
>
> thanks again.
>
> Hamu
>
>
> ------------------------------
> *From:* Anthony Holloway <avholloway+cisco-v...@gmail.com>
> *Sent:* Thursday, March 1, 2018 11:05 AM
>
> *To:* Hamu Ebiso
> *Cc:* Cisco VoIP Group
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
> According to the debug, you're calling 19529473283 <(952)%20947-3283>.
> Is that correct?
>
> Called Number=19529473283 <(952)%20947-3283>(TON=Unknown, NPI=Unknown),
>
>
> If so, then this debug is not for this gateway, because you're hitting
> Outgoing Dial-peer=5
>
> Outgoing Dial-peer=5, Params=0x688FF3FC, Progress Indication=ORIGINATING SIDE 
> IS NON ISDN(3)
>
>
> And dial-peer 5, while it exists in your config you pasted, it doesn't
> match the called number.
>
> dial-peer voice 5 voip
>  description FXO test
>  destination-pattern 12083437020 <(208)%20343-7020>
>  session target ipv4:10.0.2.5
> !
>
> Even if it did match the destination pattern, you're missing some config
> on this dial-peer to make a SIP capable dial-peer, which means it's sending
> H323 setup to CUCM.  If you built the gateway as H323, then I can see how
> it rang your CIPC, otherwise, if you built it as SIP, which you said you
> did, then it would never ring your CIPC.
>
> So, something is not adding up here.
>
> Also, you're hitting Incoming Dial-peer=0, which on a POTS leg is not too
> terrible, but it's also not good practice to be using dial-peer 0.  It's
> really VoIP DP 0 that is messy though.
>
> Incoming Dial-peer=0, Progress Indication=ORIGINATING SIDE IS NON ISDN(3), 
> Calling IE Present=FALSE,
>
>
>
> On Thu, Mar 1, 2018 at 10:06 AM Hamu Ebiso <hebiso2...@hotmail.com> wrote:
>
> Hi Anthony,
>
>
> yes the call was hitting the gateway because I was seeing FXO port going
> Off-Hook. The problem was that Logging was not setup in the gateway. After
> I setup the Logging, I'm now seeing logs.
>
>
> I have attached the log.
>
>
> thanks
>
> Hamu
> ------------------------------
> *From:* avhollo...@gmail.com <avhollo...@gmail.com> on behalf of Anthony
> Holloway <avholloway+cisco-v...@gmail.com>
> *Sent:* Thursday, March 1, 2018 8:45 AM
> *To:* Hamu Ebiso
> *Cc:* Cisco VoIP Group
>
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
> Since you didn't see the call in your debugs, your call likely didn't hit
> your gateway.
>
> Can you confirm how you made your test call, when you had your debug
> running?
>
> On Feb 28, 2018 2:46 PM, "Hamu Ebiso" <hebiso2...@hotmail.com> wrote:
>
> Here is the dial-peer output
>
> 1#show run | sec dial-peer
> dial-peer voice 1 pots
>  trunkgroup FXO_EM
>  translation-profile incoming Inbound
>  call-block translation-profile incoming block_profile
>  call-block disconnect-cause incoming call-reject
>  incoming called-number .
>  direct-inward-dial
> dial-peer voice 911 pots
>  trunkgroup FXO_EM
>  description Services
>  translation-profile outgoing Strip9
>  destination-pattern 911
> dial-peer voice 9911 pots
>  trunkgroup FXO_EM
>  description Services
>  translation-profile outgoing Strip9
>  destination-pattern 9911
> dial-peer voice 2 voip
>  description CUCM Dial-Peer - Inbound
>  preference 1
>  destination-pattern 12086858038 <(208)%20685-8038>
>  session protocol sipv2
>  session target ipv4:10.0.2.6
>  incoming uri via 10
>  voice-class codec 1
>  dtmf-relay rtp-nte sip-kpml
>  fax-relay ecm disable
>  fax nsf 000000
>  ip qos dscp cs3 signaling
>  no vad
> dial-peer voice 3 voip
>  preference 2
>  destination-pattern 12086858038 <(208)%20685-8038>
>  session target ipv4:10.0.2.3
> dial-peer voice 650 pots
>  trunkgroup Local
>  description Local outbound
>  translation-profile outgoing Strip9
>  destination-pattern 9208.......
> dial-peer voice 4 pots
>  trunkgroup FXO_EM
>  description ** 10-digit Local Call **
>  translation-profile outgoing Strip9
>  destination-pattern ^9[2-9]..[2-9]......$
>  forward-digits 10
> dial-peer voice 5 voip
>  description FXO test
>  destination-pattern 12083437020 <(208)%20343-7020>
>  session target ipv4:10.0.2.5
>
>
> thank you very much!!
>
> ------------------------------
> *From:* Anthony Holloway <avholloway+cisco-v...@gmail.com>
> *Sent:* Wednesday, February 28, 2018 1:29 PM
> *To:* Hamu Ebiso
> *Cc:* cisco-voip voyp list
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
>
> Maybe you're actually using MGCP then?  You still haven't shown the
> dial-peers on the gateway.  Is that because you don't have any?
>
> show run | section dial-peer
>
> On Wed, Feb 28, 2018 at 12:19 PM Hamu Ebiso <hebiso2...@hotmail.com>
> wrote:
>
> debug was turned on as shown below.
>
>
> 1#debug voice ccapi inout
> voip ccapi inout debugging is on
>
> made test calls and then show log, I see below output.
>
> 1#show log
> Syslog logging: enabled (0 messages dropped, 37 messages rate-limited, 0
> flushes, 0 overruns, xml disabled, filtering disabled)
>
> No Active Message Discriminator.
>
>
> No Inactive Message Discriminator.
>
>
>     Console logging: level debugging, 517 messages logged, xml disabled,
>                      filtering disabled
>     Monitor logging: level debugging, 0 messages logged, xml disabled,
>                      filtering disabled
>     Buffer logging:  level debugging, 550 messages logged, xml disabled,
>                     filtering disabled
>     Exception Logging: size (4096 bytes)
>     Count and timestamp logging messages: disabled
>     Persistent logging: disabled
>
> No active filter modules.
>
>     Trap logging: level debugging, 620 message lines logged
>         Logging to 10.0.7.139  (udp port 514, audit disabled,
>               link up),
>               435 message lines logged,
>               0 message lines rate-limited,
>               0 message lines dropped-by-MD,
>               xml disabled, sequence number disabled
>               filtering disabled
>         Logging to 10.0.8.12  (udp port 514, audit disabled,
>               link up),
>               435 message lines logged,
>               0 message lines rate-limited,
>               0 message lines dropped-by-MD,
>               xml disabled, sequence number disabled
>               filtering disabled
>         Logging Source-Interface:       VRF Name:
>         Loopback0
>
>
> I don't see any calls activity.
>
>
> thanks
>
> ------------------------------
> *From:* Anthony Holloway <avholloway+cisco-v...@gmail.com>
> *Sent:* Wednesday, February 28, 2018 11:19 AM
>
> *To:* Hamu Ebiso
> *Cc:* cisco-voip voyp list
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
> But you didn't send all the information, because your output doesn't show
> the dial-peers.
>
> One method is to capture the output from "debug voip ccapi inout" and look
> for the following line "Outgoing Dial-peer="
>
> You also didn't address the regions either.  Can you send that too?
>
> On Wed, Feb 28, 2018 at 11:13 AM Hamu Ebiso <hebiso2...@hotmail.com>
> wrote:
>
> I was just trying to give you all the information so that you will be able
> to see the whole picture.
>
> Regarding your questions, I don't know how to check that.
>
>
> ------------------------------
> *From:* Anthony Holloway <avholloway+cisco-v...@gmail.com>
> *Sent:* Wednesday, February 28, 2018 10:45 AM
>
> *To:* Hamu Ebiso
> *Cc:* cisco-voip voyp list
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
> That's interesting that I asked for the dial-peer config, and you sent
> everything but.
>
> Do you know how to confirm which dial-peer the gateway is using?
>
> On Wed, Feb 28, 2018 at 10:38 AM Hamu Ebiso <hebiso2...@hotmail.com>
> wrote:
>
> Below is gateway configuration
>
>
>
>
> isdn switch-type primary-ni
> !
> !
> trunk group FXO_EM
>  hunt-scheme sequential
>  translation-profile incoming Incoming
> !
> !
> trunk group Local
>  hunt-scheme sequential
>  translation-profile outgoing outbound
> !
> !
> trunk group LD
>  translation-profile outgoing outbound
> !
> voice-card 0
>  dspfarm
>  dsp services dspfarm
> !
> !
> voice call send-alert
> voice rtp send-recv
> !
> voice service voip
>  ip address trusted list
>   ipv4 10.170.99.12
>   ipv4 10.44.50.14
>   ipv4 10.44.50.39
>  no ip address trusted authenticate
>  clid substitute name
>  clid network-provided
>  allow-connections h323 to h323
>  allow-connections h323 to sip
>  allow-connections sip to h323
>  allow-connections sip to sip
>  redirect ip2ip
>  signaling forward unconditional
>  fax protocol t38 nse force version 0 ls-redundancy 0 hs-redundancy 0
> fallback pass-through g711ulaw
>  no fax-relay sg3-to-g3
>  modem passthrough nse codec g711ulaw
>  sip
>   bind control source-interface Loopback0
>   bind media source-interface Loopback0
>   session transport tcp
>   min-se 360 session-expires 360
>   ds0-num
>   header-passing
>   error-passthru
>   registrar server expires max 600 min 60
>   early-offer forced
>   midcall-signaling passthru
>   no call service stop
> !
> !
> voice class uri 10 sip
>  host ipv4:10.x.x.x
>  host ipv4:10..x.x.x
>  host ipv4:10..x.x.x
> voice class codec 1
>  codec preference 1 g711ulaw
>  codec preference 2 g729r8
> !
> voice class codec 2
>  codec preference 1 g711ulaw
> !
> !
> !
> !
> voice translation-rule 1
>  rule 1 /^208343\(....\)$/ /1208343\1/
> !
> voice translation-rule 9
>  rule 1 /5.../ /1208343\0/
> !
> voice translation-rule 10
>  rule 1 /^911/ /911/
>  rule 2 /^9911/ /911/
> !
> voice translation-rule 15
> !
> voice translation-rule 30
>  rule 1 /^911/ /911/
>  rule 2 /^9911/ /911/
>  rule 4 /^9\(011.*\)/ /\1/
>  rule 9 /^9\(.*\)/ /\1/
> !
> !
> voice translation-profile Add1
>  translate calling 91
>  translate called 1
> !
> voice translation-profile Inbound
>  translate called 1
> !
> voice translation-profile Strip9
>  translate called 10
> !
> voice translation-profile block_profile
>  translate calling 15
> !
> voice translation-profile outbound
>  translate calling 10
> !
> !
> crypto pki token default removal timeout 0
> !
> !
> !
> !
> license udi pid CISCO3845-MB sn FOC123128X5
> license accept end user agreement
> archive
>  log config
>   hidekeys
> username admin privilege 15 password 7 105D1F0C
> username svuntbd privilege 15 secret 5 $1$vRxN$nu4JPZttcuPskPHoSdQZx.
> !
> !
> controller T1 0/0/0
>  shutdown
>  cablelength long 0db
> !
> controller T1 0/1/0
>  shutdown
>  cablelength long 0db
> !
> !
> !
> !
> !
> !
> interface Loopback0
>  ip address 10.x.x.x 255.255.255.128
> !
> interface GigabitEthernet0/0
>  description uplink to Lan1
>  ip address 10.x.x.x 255.255.255.252
>  duplex auto
>  speed auto
>  media-type rj45
> !
> interface GigabitEthernet0/1
>  description uplink to Lan2
>  ip address 10.x.x.x 255.255.255.252
>  duplex auto
>  speed auto
>  media-type rj45
> !
> router ospf 1
>  auto-cost reference-bandwidth 10000
>  network 10.0.0.0 0.0.255.255 area 10.0.0.0
> !
> ip forward-protocol nd
> !
> !
> no ip http server
> no ip http secure-server
> !
>
>
>
_______________________________________________
cisco-voip mailing list
cisco-voip@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip

Reply via email to