Again, I have heard rumors but have yet to see it. Do you have any config
examples?
Evgeny Babanin <[EMAIL PROTECTED]> wrote in message
8jppgf$qu4$[EMAIL PROTECTED]">news:8jppgf$qu4$[EMAIL PROTECTED]...
> Network Side PRI SIgnalling first was introduced in 12.1(2)XH version of
> IOS,
>
>
> RGRDS,
> Evgeny
>
> "Chris Larson" <[EMAIL PROTECTED]> wrote in message
> 009AE8FD8584D3119A2E0008C7F4A84929D2@WEBSERVER">news:009AE8FD8584D3119A2E0008C7F4A84929D2@WEBSERVER...
> > I had heard rumors about this, but have never heard of anyone doing it.
> >
> > I tried this on my 3640 running 12.0(7) and there is no ISDN network
> > command. Maybe you need enterprise IOS (I am running IP Plus IPSEC).
There
> > is a way to set TEI statically, but I do not think that would be
> sufficient.
> > I did not follow through with a complete config.
> >
> > -----Original Message-----
> > From: K Sacca [mailto:[EMAIL PROTECTED]]
> > Sent: Friday, June 30, 2000 4:54 PM
> > To: Daniel Cotts; '[EMAIL PROTECTED]'; '[EMAIL PROTECTED]'
> > Subject: RE: Need help
> >
> >
> > Try the following and see if it works. I was provided
> > this information by a colleague.
> >
> > Are you trying to set up a back-to-back connection
> > using ISDN ? If
> > that's the case, on the peer serial0:23 interace, you
> > need to issue the
> > command ISDN network. This simulates the network
> > (switch) side of the
> > ISDN connection.
> >
> > You can verify that by doing 'show isdn status' and it
> > should say
> > '**network side configuration'. Be careful with clock
> > sources tho.
> > Generally I make the side which is acting as the
> > network use the
> > internal clock. This can be done by doing 'clock
> > source internal' on the
> > t1 controller
> >
> > Regards Kamoto
> >
> >
> > --- Daniel Cotts <[EMAIL PROTECTED]> wrote:
> > > First you need two routers with an ISDN BRI
> > > interface. Note some have a U
> > > interface for USA connections while others have an
> > > S/T interface that is
> > > used in the rest of the world. Note that a NT-1
> > > adapter converts the S/T on
> > > the router to interact with the U provided by the
> > > Telco.
> > > To connect them you must either have the Telco
> > > provide ISDN service or
> > > purchase an ISDN simulator. Two manufacturers of
> > > simulators are:
> > > 1) Arca Technologies - call Dean Coleman
> > > 800-888-1978 ext 252 also
> > > www.arca.com Lotsa toys!
> > > 2)Teltone check out www.teltone.com or talk to
> > > communications distributors
> > > such as Graybar or Anixter, etc. Also Specialized
> > > Products 800-866-5353.
> > > Good service but most likely not the lowest price.
> > > Simulators are expensive.
> > >
> > > > -----Original Message-----
> > > > From: [EMAIL PROTECTED]
> > > [mailto:[EMAIL PROTECTED]]
> > > > Sent: Thursday, June 29, 2000 8:23 PM
> > > > To: [EMAIL PROTECTED]
> > > > Subject: Need help
> > > >
> > > >
> > > > Any Ideas on how can I configure a lab network to
> > > simulate
> > > > ISDN can a cisco
> > > > router do this job if yes which router.
> > > >
> > > > Regards,
> > > > Amir
> > > >
> > > > ___________________________________
> > > > UPDATED Posting Guidelines:
> > > http://www.groupstudy.com/list/guide.html
> > > > FAQ, list archives, and subscription info:
> > > http://www.groupstudy.com
> > > > Report misconduct and Nondisclosure violations to
> > > [EMAIL PROTECTED]
> > > >
> > >
> > > ___________________________________
> > > UPDATED Posting Guidelines:
> > > http://www.groupstudy.com/list/guide.html
> > > FAQ, list archives, and subscription info:
> > > http://www.groupstudy.com
> > > Report misconduct and Nondisclosure violations to
> > [EMAIL PROTECTED]
> >
> >
> > __________________________________________________
> > Do You Yahoo!?
> > Get Yahoo! Mail - Free email you can access from anywhere!
> > http://mail.yahoo.com/
> >
> > ___________________________________
> > UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
> > FAQ, list archives, and subscription info: http://www.groupstudy.com
> > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
> >
> > ___________________________________
> > UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
> > FAQ, list archives, and subscription info: http://www.groupstudy.com
> > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
> > ---
>
>
> ___________________________________
> UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
> FAQ, list archives, and subscription info: http://www.groupstudy.com
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
>
___________________________________
UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
FAQ, list archives, and subscription info: http://www.groupstudy.com
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
