You can look at it that way.. Instead of having a switch and a router you actually 1 device with one IOS running that does the job of both other devices..
Larry Letterman Network Engineer Cisco Systems > -----Original Message----- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of > DeVoe, Charles (PKI) > Sent: Thursday, April 03, 2003 1:01 PM > To: [EMAIL PROTECTED] > Subject: RE: Hybrid vs. Native [7:66766] > > > So if I read this right, it is just a different set of commands. > Are there > operational differences? > > -----Original Message----- > From: MADMAN [mailto:[EMAIL PROTECTED] > Sent: Thursday, April 03, 2003 3:44 PM > To: DeVoe, Charles (PKI) > Cc: [EMAIL PROTECTED] > Subject: Re: Hybrid vs. Native [7:66766] > > > DeVoe, Charles (PKI) wrote: > > We have a 6509 and I have heard talk about native vs. Hybrid mode of > > operation. What is the difference? Is there a link to a > white paper or > > something? > That question comes up periodically but the in a nutshell a 6500 in > native mode is a big router, no catOS commands, and if you are familiar > with 2900/3500 switch commands native switch layer 2 stuff will be > familiar and of coarse the L3 commands are your regualr old IOS > commands. Here is a snap shot of a 6506 running native: > > Native6506#sh ha > Cisco Internetwork Operating System Software > IOS (tm) c6sup2_rp Software (c6sup2_rp-JS-M), Version 12.1(13)E, EARLY > DEPLOYMEN > T RELEASE SOFTWARE (fc1) > TAC Support: http://www.cisco.com/tac > Copyright (c) 1986-2002 by cisco Systems, Inc. > Compiled Wed 04-Sep-02 18:45 by eaarmas > Image text-base: 0x40008C00, data-base: 0x41A68000 > > ROM: System Bootstrap, Version 12.1(4r)E, RELEASE SOFTWARE (fc1) > BOOTLDR: c6sup2_rp Software (c6sup2_rp-JS-M), Version 12.1(13)E, EARLY > DEPLOYMEN > T RELEASE SOFTWARE (fc1) > > Native6506 uptime is 5 weeks, 2 days, 43 minutes > Time since Native6506 switched to active is 5 weeks, 2 days, 42 minutes > System returned to ROM by power-on (SP by power-on) > System image file is "slot0:c6sup12-js-mz.121-13.E.bin" > > cisco Catalyst 6000 (R7000) processor with 112640K/18432K bytes of memory. > Processor board ID SAD05020HUX > R7000 CPU at 300Mhz, Implementation 39, Rev 2.1, 256KB L2, 1024KB L3 Cache > Last reset from power-on > Bridging software. > X.25 software, Version 3.0.0. > SuperLAT software (copyright 1990 by Meridian Technology Corp). > TN3270 Emulation software. > 8 Virtual Ethernet/IEEE 802.3 interface(s) > 120 FastEthernet/IEEE 802.3 interface(s) > 4 Gigabit Ethernet/IEEE 802.3 interface(s) > 381K bytes of non-volatile configuration memory. > > 16384K bytes of Flash internal SIMM (Sector size 512K). > Standby is up > Standby has 112640K/18432K bytes of memory. > > Configuration register is 0x2102 > > Native6506# > > Native6506#sh conf > Using 8789 out of 391160 bytes > ! > version 12.1 > service timestamps debug uptime > service timestamps log uptime > no service password-encryption > ! > hostname Native6506 > ! > boot system flash slot0:c6sup12-js-mz.121-13.E.bin > boot bootldr bootflash:c6msfc2-boot-mz.121-4.E1 > no logging console > enable password cisco > ! > ip subnet-zero > ! > ! > ip tcp intercept mode watch > no ip domain-lookup > ! > mls flow ip destination > mls flow ipx destination > ! > redundancy > mode rpr-plus > main-cpu > auto-sync running-config > auto-sync standard > ! > ! > ! > interface Port-channel1 > no ip address > switchport > switchport trunk encapsulation dot1q > ! > interface GigabitEthernet1/1 > no ip address > switchport > switchport trunk encapsulation dot1q > switchport trunk native vlan 64 > ! > interface GigabitEthernet1/2 > no ip address > shutdown > ! > interface FastEthernet3/1 > no ip address > duplex full > speed 100 > switchport > switchport access vlan 301 > switchport trunk encapsulation dot1q > switchport mode trunk > ! > interface FastEthernet3/2 > ip address 121.1.1.2 255.255.255.0 > duplex full > speed 100 > ! > interface FastEthernet3/3 > ip address 30.1.1.1 255.255.255.0 > ip access-group 199 in > duplex half > speed 100 > ! > interface FastEthernet3/4 > no ip address > duplex half > speed 10 > switchport > switchport access vlan 304 > switchport mode access > !interface Vlan1 > no ip address > shutdown > ! > interface Vlan64 > ip address 172.28.64.23 255.255.255.0 > ! > interface Vlan302 > ip address 79.79.79.1 255.255.255.0 > ip access-group 199 in > ! > interface Vlan303 > ip address 99.13.13.1 255.255.255.0 > shutdown > ! > interface Vlan304 > ip address 79.79.80.1 255.255.255.0 > ! > interface Vlan305 > ip address 99.15.15.1 255.255.255.0 > shutdown > ! > interface Vlan306 > no ip address > shutdown > ! > interface Vlan307 > no ip address > ! > router eigrp 1 > network 172.28.0.0 > no auto-summary > eigrp log-neighbor-changes > ! > router eigrp 100 > network 99.0.0.0 > no auto-summary > no eigrp log-neighbor-changes > ! > ip classless > no ip http server > > > > > -- > David Madland > CCIE# 2016 > Sr. Network Engineer > Qwest Communications > 612-664-3367 > > I would rather have a German division in front of me than a French one > behind me." > --- General George S. Patton Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=66800&t=66766 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
