Hi group,
I recently got a ILS-1000 ISDN simulator for my lab, I config two router
according to the CCIE LAB configuration and i just can not make the BRI
dial.
Did anyone have any experience for the this simulator.
Here is the output and the config, pleas help.....
R2503#
interface BRI0
ip address 100.100.100.200 255.255.255.0
encapsulation ppp
dialer idle-timeout 90
dialer map ip 100.100.100.100 name r2521
dialer-group 1
isdn switch-type basic-ni
isdn spid1 0835866201
isdn spid2 0835866401
no fair-queue
ppp multilink
!
no ip classless
ip route 100.0.0.0 255.255.255.0 BRI0
ip route 196.1.1.0 255.255.255.0 BRI0
no ip http server
no ip pim bidir-enable
!
dialer-list 1 protocol ip permit
!
r2521#
interface BRI0
ip address 100.100.100.100 255.255.255.0
ip directed-broadcast
encapsulation ppp
dialer idle-timeout 90
dialer map ip 100.100.100.200 name r2503 broadcast 8358662
dialer load-threshold 1 outbound
dialer-group 1
isdn switch-type basic-ni
isdn spid1 0835866101
isdn spid2 0835866301
no fair-queue
ppp multilink
!
router rip
network 100.0.0.0
!
ip nat translation timeout never
ip nat translation tcp-timeout never
ip nat translation udp-timeout never
ip nat translation finrst-timeout never
ip nat translation syn-timeout never
ip nat translation dns-timeout never
ip nat translation icmp-timeout never
ip classless
!
dialer-list 1 protocol ip permit
r2503#sh isdn status
Global ISDN Switchtype = basic-ni
ISDN BRI0 interface
dsl 0, interface ISDN Switchtype = basic-ni
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 119, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
TEI = 121, Ces = 2, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
TEI 119, ces = 1, state = 5(init)
spid1 configured, no LDN, spid1 sent, spid1 valid
Endpoint ID Info: epsf = 0, usid = 2, tid = 1
TEI 121, ces = 2, state = 5(init)
spid2 configured, no LDN, spid2 sent, spid2 valid
Endpoint ID Info: epsf = 0, usid = 4, tid = 1
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 0 CCBs = 0
The Free Channel Mask: 0x80000003
Number of L2 Discards = 0, L2 Session ID = 52
Total Allocated ISDN CCBs = 0
r2503#sh int bri0
BRI0 is up, line protocol is up (spoofing)
Hardware is BRI
Internet address is 100.100.100.200/24
MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, loopback not set
Last input 00:00:29, output 00:00:29, output hang never
Last clearing of "show interface" counters 01:01:09
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue :0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
302 packets input, 1536 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
326 packets output, 1696 bytes, 0 underruns
0 output errors, 0 collisions, 8 interface resets
0 output buffer failures, 0 output buffers swapped out
19 carrier transitions
Thank you very much..
Philip Lee
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=70856&t=70856
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
