hi ,
I have problems with my frame-relay serial link attatched is the router
configuration
physical layer confirmed is ok as carrier is up but my serial interface
still showing interface up line protocol down
Any inputs will be greatly appreciated
thanks
Jason
cncnepal.384.128.k2pop#sh run
Building configuration...
Current configuration:
!
version 11.2
no service password-encryption
no service udp-small-servers
no service tcp-small-servers
!
hostname cncnepal.384.128.k2pop
!
!
ip subnet-zero
!
interface Ethernet0
no ip address
!
interface Serial0
ip address 192.168.1.9 255.255.255.252
no fair-queue
!
interface Serial1
no ip address
encapsulation frame-relay IETF
--More--
frame-relay lmi-type ansi
!
interface Serial1.1 point-to-point
ip address 202.161.128.158 255.255.255.252
frame-relay interface-dlci 659
!
router bgp 64519
network 202.51.65.0
network 202.51.66.0
!
ip classless
ip route 0.0.0.0 0.0.0.0 202.161.128.157
!
line con 0
line 1 16
line aux 0
line vty 0 4
password router
login
!
end
cncnepal.384.128.k2pop#sh int s1
Serial1 is up, line protocol is down
Hardware is HD64570
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, rely 168/255, load 1/255
Encapsulation FRAME-RELAY IETF, loopback not set, keepalive set (10 sec)
LMI enq sent 60, LMI stat recvd 0, LMI upd recvd 0, DTE LMI down
LMI enq recvd 0, LMI stat sent 0, LMI upd sent 0
LMI DLCI 0 LMI type is ANSI Annex D frame relay DTE
Broadcast queue 0/64, broadcasts sent/dropped 1/0, interface broadcasts 0
Last input never, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0 (size/max/drops); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
12363 input errors, 38 CRC, 0 frame, 36 overrun, 739 ignored, 38 abort
62 packets output, 1162 bytes, 0 underruns
0 output errors, 0 collisions, 21 interface resets
0 output buffer failures, 0 output buffers swapped out
--More--
0 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
cncnepal.384.128.k2pop#sh log
Syslog logging: enabled (0 messages dropped, 0 flushes, 0 overruns)
Console logging: level debugging, 13 messages logged
Monitor logging: level debugging, 0 messages logged
Trap logging: level informational, 17 message lines logged
Buffer logging: level debugging, 13 messages logged
--More--
Log Buffer (4096 bytes):
%LINK-3-UPDOWN: Interface Ethernet0, changed state to up
%LINK-3-UPDOWN: Interface Serial0, changed state to down
%LINK-3-UPDOWN: Interface Serial1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to up
%FR-5-DLCICHANGE: Interface Serial1 - DLCI 659 state changed to ACTIVE
%SYS-5-CONFIG_I: Configured from memory by console
%SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) 2500 Software (C2500-I-L), Version 11.2(18), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1999 by cisco Systems, Inc.
Compiled Mon 05-Apr-99 19:52 by jaturner
%FR-5-DLCICHANGE: Interface Serial1 - DLCI 659 state changed to INACTIVE
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1.1, changed state to down
%FR-5-DLCICHANGE: Interface Serial1 - DLCI 659 state changed to DELETED
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to down
cncnepal.384.128.k2pop#
