Robert, from my experience with bridging VLAN traffic between two LANE modules, the
entire VLAN database is not bridged over a PVC, only the individual VLAN that is bound
to it. If you want all of the VLANs to be accessable by the remote switch, then you
will
need a PVC per VLAN.
Willie Bell
CCIE# 6075, CCDP
email [EMAIL PROTECTED]
"McCallum, Robert" wrote:
> Hi ,
>
> Scenario is 2 cat 5509's connected together with an STM-1. Both are in the
> same VTP domain but will not speak to each other. Configs are pasted below.
> I DO NOT want to have management traffic (vlan 1) traversing across this
> link. This link is working just VTP is not traversing. First question is
> Does LANE trunking allow VTP to cross?
>
> CAT 1
>
> set vtp domain BSKYB
> set vtp mode server
> set vtp v2 disable
> set vtp pruning enable
> #spantree
> #uplinkfast groups
> set spantree uplinkfast enable rate 15 all-protocols off
> #backbonefast
> set spantree backbonefast enable
> set spantree enable all
> #module 9 : 2-port SM OC-3 Dual-Phy ATM
> set module name 9
> set port level 9/1 normal
> set port name 9/1-2
> set cdp enable 9/1
> set cdp interval 9/1 60
> set trunk 9/1 on lane 1-1005
> set spantree portcost 9/1 3014
> set spantree portpri 9/1 32
> set spantree portvlanpri 9/1 0
> set spantree portvlancost 9/1 cost 3013
>
> on the atm card
>
> sess 9
>
> interface ATM0
> atm preferred phy A
> atm pvc 1 2 50 aal5snap
> atm pvc 2 2 60 aal5snap
> atm bind pvc vlan 1 10
> atm bind pvc vlan 2 2
>
> CAT 2
>
> set vtp domain BSKYB
> set vtp mode server
> set vtp v2 disable
> set vtp pruning enable
> #spantree
> #uplinkfast groups
> set spantree uplinkfast enable rate 15 all-protocols off
> #backbonefast
> set spantree backbonefast enable
> set spantree enable all
> #module 9 : 2-port SM OC-3 Dual-Phy ATM
> set module name 9
> set port level 9/1 normal
> set port name 9/1-2
> set cdp enable 9/1
> set cdp interval 9/1 60
> set trunk 9/1 on lane 1-1005
> set spantree portcost 9/1 3014
> set spantree portpri 9/1 32
> set spantree portvlanpri 9/1 0
> set spantree portvlancost 9/1 cost 3013
>
> interface ATM0
> atm preferred phy A
> atm sonet stm-1
> atm uni-version 3.1
> atm pvc 1 2 50 aal5snap
> atm pvc 2 2 60 aal5snap
> atm pvc 3 0 5 qsaal
> atm pvc 4 0 16 ilmi
> atm bind pvc vlan 1 10
> atm bind pvc vlan 2 2
>
> Any help much appreciated.
>
> P.S. cdp IS working over this ATM link.
>
> _________________________________
> FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
--
_________________________________
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
