has anybody thoguth that this router has an IOS and is not booting from the correct
partition? It cannot route packets because the IOS was not fiully loaded. All
routers come with default software. Check to see if there is a boot system flash
statement. Make sure the IOS it is calling is calling it from the correct partition
and the name is correct.
sh flash detail
>>> "Quadri, Habeeb" <[EMAIL PROTECTED]> 12/06/00 10:32AM >>>
If a router has ethernet interface, as shown in "sh ver" then activate the
interface by giving it an ip address. If you don't want to connect to live
network then use a simple class C ip address, configure a laptop (tftp
server)with another ip address in the same subnet, use tftp download.
Config register setting 0x2102 is not a problem in this case.
> -----Original Message-----
> From: Larry Ogun-Banjo [SMTP:[EMAIL PROTECTED]]
> Sent: Wednesday, December 06, 2000 6:37 AM
> To: Atef Rostom
> Cc: [EMAIL PROTECTED]
> Subject: Re: Router(boot)#
>
> I had a similar problem recently. I was able to solve this by going to the
> global configuration mode and changing the configuration register
> settings. I
> hope this helps.
>
>
>
>
> "Atef Rostom" <[EMAIL PROTECTED]> on 12/06/2000 11:39:04 AM
>
> Please respond to "Atef Rostom" <[EMAIL PROTECTED]>
>
> To: [EMAIL PROTECTED]
> cc: (bcc: Larry Ogun-Banjo/EN/Kpn-Orange)
>
> Subject: Re: Router(boot)#
>
>
>
> Another slow but solid way to upload a new image to the router is xmodem.
>
> Put the image on the machine you have connected to the router's console,
> then
>
> xmodem <filename>
>
> and when you have the "ready to receive message ... " use you terminal
> application to send the file using the X-Modem Protocol.
>
> Win Hyperterm, File transfer menu, send file option.
>
> This will also load/start the IOS as soon as the upload is complete, if
> you
> don't want it to start, add -x to the xmodem command.
>
> This is s..l..o..w.. I repeat, usually 9600 compared to the TFTP 10000000,
> but solid and reliable.
>
> Good luck.
>
> Atef Rostom
>
>
> "md. nazri" <
>
>
> "md. nazri" <[EMAIL PROTECTED]> wrote in message
> 010901c03cab$f580b160$[EMAIL PROTECTED]">news:010901c03cab$f580b160$[EMAIL PROTECTED]...
> hi all,
> I got a problem with my 2500 router, anybody pls xplain what the (boot)
> means..i can't even show my routing table...i copied sh ver o/p...
>
>
> KB(boot)>sh ver
> Cisco Internetwork Operating System Software
> IOS (tm) 3000 Bootstrap Software (IGS-BOOT-R), Version 11.0(10c), RELEASE
> SOFTWARE (fc1)
> Copyright (c) 1986-1996 by cisco Systems, Inc.
> Compiled Fri 27-Dec-96 17:33 by loreilly
> Image text-base: 0x01010000, data-base: 0x00001000
>
> ROM: System Bootstrap, Version 11.0(10c), SOFTWARE
>
> KB uptime is 34 minutes
> System restarted by power-on
> Running default software
>
> cisco 2500 (68030) processor (revision N) with 6144K/2048K bytes of
> memory.
> Processor board ID 09940323, with hardware revision 00000001
> X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.
> Basic Rate ISDN software, Version 1.0.
> 1 Ethernet/IEEE 802.3 interface.
> 2 Serial network interfaces.
> 1 ISDN Basic Rate interface.
> 32K bytes of non-volatile configuration memory.
> 8192K bytes of processor board System flash (Read/Write)
>
> Configuration register is 0x2102
>
> KB(boot)>
>
>
> KB(boot)#sh ip rou
> ^
> % Invalid input detected at '^' marker.
>
> KB(boot)#
>
>
> tq
>
> rgds
> nazri
>
>
> _________________________________
> FAQ, list archives, and subscription info:
> http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
>
>
>
>
>
>
> _________________________________
> FAQ, list archives, and subscription info:
> http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
_________________________________
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
_________________________________
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
