The RSM can be placed in any slot except for 1
(reserved for Supervisor) and 13 (reserved for ASP).
If you plan on using the ATM cell switching backplane
I would recommend placing the RSM in an upper slot
(9-12 are cell backplane capable). The RSM will only
communicate with a single 1.2 Gbps backplane of the 3
enabled with the Phoenix ASIC, so it doesn't matter
which slot of the 2-12 it is placed in.
The RSM will down an interface if no physical port in
the logical VLAN is active. This means that the switch
must be configured and the port must be active. As
noted previously, this might be the source of the
problem. Using the 'show interface' command will
resolve this consideration.
I have seen issues with older versions of code and
mis-matched speed/duplex cause the RSM to fail to
up/up. I'd recommend 4.5.5 at a minimum, and 12.0.9
for the RSM. Look at the ports also - use the switch
to verify that it can see the 'connected' switch at
Layer 2 - the RSM will not see things correctly if the
Supervisor does not.
--- fmxiao <[EMAIL PROTECTED]> wrote:
> We've always put the RSM in Slot 4...
>
>
> "Mark Krysinski" <[EMAIL PROTECTED]> wrote in
> message
>
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> > Are you sure you can plug the RSM into slot #2. I
> remember someone
> telling
> > me to have it in slot 12. Please let me know if
> this is the case, our
> 5500
> > uses slot 2 for a back up sup III module and slot
> 12 for the RSM with Vip
> > module.
> >
> > Hope this helps.
> >
> > Mark
> >
> > -----Original Message-----
> > From: [EMAIL PROTECTED]
> [mailto:[EMAIL PROTECTED]]On Behalf Of
> > viathin
> > Sent: Wednesday, December 20, 2000 6:59 PM
> > To: [EMAIL PROTECTED]
> > Subject: Re: problems configuring a 5500 chasis
> please help
> >
> >
> > I tried plugging in an active switch into vlan
> 100 and it still was
> saying
> > that the vlan was not active or at least it
> appeared that way and i
> couldn't
> > ping it.
> >
> > ""Brian Gleason"" <[EMAIL PROTECTED]>
> wrote in message
> > 91qoiu$1kf$[EMAIL PROTECTED]">news:91qoiu$1kf$[EMAIL PROTECTED]...
> > >
> > > Try plugging in a client machine into each of
> your vlans. I had this
> > > problem with a 6509 and once the client link
> state came up, the
> interface
> > > came up.
> > >
> > >
> > > ""viathin"" <[EMAIL PROTECTED]> wrote in
> message
> > > 91plqc$2ti$[EMAIL PROTECTED]">news:91plqc$2ti$[EMAIL PROTECTED]...
> > > > I'm having trouble configuring one router was
> wondering if you could
> > help
> > > >
> > > > We are configuring a 5500 Chassis with:
> > > > > >
> > > > > > 1) WS X5530 Supervisor Engine (Slot 1)
> > > > > > 2) WS X5302 Route Switch Module (Slot 2)
> > > > > > 3) WS 5224 Switch ports (24 copper ports)
> > > > > >
> > > > > > A)
> > > > > > We have defined:
> > > > > > VLAN 100 on 3/1-4
> > > > > > VLAN 200 on 3/5-8
> > > > > > VLAN 300 on 3/9-12
> > > > > > VLAN 500 on 3/21-24
> > > > > > B)
> > > > > > We have created the interfaces on the RSM:
> > > > > > Config Terminal:
> > > > > > 1) Interface vlan 100
> > > > > > ip address 192.170.1.1 255.255.255.0
> > > > > > 2) Interface vlan 200
> > > > > > ip address 192.170.2.1 255.255.255.0
> > > > > > 3) Interface vlan 300
> > > > > > ip address 192.170.3.1 255.255.255.0
> > > > > > 5) Interface vlan 500
> > > > > > ip address 192.170.5.1 255.255.255.0
> > > > > >
> > > > > > Performed a no shutdown command on all
> interfaces.
> > > > > >
> > > > > > C)
> > > > > > We implemented "eigrp 1" as the routing
> protocol using:
> > > > > > Interface vlan 100
> > > > > > router eigrp 1
> > > > > > network 192.170.1.0
> > > > > > network 192.170.2.0
> > > > > > network 192.170.3.0
> > > > > > network 192.170.5.0
> > > > > > The above was repeated for all vlans
> (100,200,300,500)
> > > > > > D)
> > > > > > 1) Can not ping any vlan interfaces.
> > > > > > 2) Performed a "Show Interface" and it
> shows all interfaces are
> > down.
> > > > > >
> > > > > >
> > > > > > Thanks for looking into this and we
> appreciate any insight on this
> > > > > > problem.
> > > > > >
> > > > > Craig.
> > > >
> > > >
> > > >
> > > > _________________________________
> > > > FAQ, list archives, and subscription info:
> > > http://www.groupstudy.com/list/cisco.html
> > > > Report misconduct and Nondisclosure violations
> to [EMAIL PROTECTED]
> > > >
> > >
> > >
> > > _________________________________
> > > FAQ, list archives, and subscription info:
> > http://www.groupstudy.com/list/cisco.html
> > > Report misconduct and Nondisclosure violations
> to [EMAIL PROTECTED]
> > >
> >
> >
> > _________________________________
> > FAQ, list archives, and subscription info:
> > http://www.groupstudy.com/list/cisco.html
> > Report misconduct and Nondisclosure violations to
> [EMAIL PROTECTED]
> >
> > _________________________________
> > FAQ, list archives, and subscription info:
> http://www.groupstudy.com/list/cisco.html
> > Report misconduct and Nondisclosure violations to
> [EMAIL PROTECTED]
> >
>
>
> _________________________________
> FAQ, list archives, and subscription info:
> http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to
[EMAIL PROTECTED]
=====
Robert Padjen
__________________________________________________
Do You Yahoo!?
Yahoo! Photos - Share your holiday photos online!
http://photos.yahoo.com/
_________________________________
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
