The one I have is also very simple
line aux 0
exec-time 0 0
modem inOut
transport input all
autohangup
flowcontrol hardware
Sam
----- Original Message -----
From: "Joseph Ezerski" <[EMAIL PROTECTED]>
To: "'Adam Quiggle'" <[EMAIL PROTECTED]>; "Sam"
<[EMAIL PROTECTED]>; <[EMAIL PROTECTED]>
Sent: Friday, January 05, 2001 12:01 AM
Subject: RE: Modem access from Router
> As far as using the AUX port, I have been able to get by with the
following
> minimal config:
>
> line aux 0
> exec-timeout 30 0
> password xxxxxxxxx (your own password here)
> modem InOut
> modem autoconfigure discovery
> transport input all
> stopbits 1
>
> Mind you, I had a USR Sportster attached to the aux port, which is listed
in
> the modemcap database, thus allowing me to squeek by with an autoconfigure
> discovery command. If you have some other model that is not in the
> modemcap, then you may have to add a few more lines. Also, if a password
is
> not necessary, nor a timeout period, you could also delete those lines.
>
> Less is more!
>
> Joseph
>
>
> -----Original Message-----
> From: Adam Quiggle [mailto:[EMAIL PROTECTED]]
> Sent: Thursday, January 04, 2001 3:21 AM
> To: Sam; [EMAIL PROTECTED]
> Subject: Re: Modem access from Router
>
>
> Sam,
>
> Here is a sample config from a 2501 that gives you PPP access to your
> network through the aux port. Don't worry about the missing lines because
> I've pulled stuff out that wasn't relevant to your question as well as
> stuck some stuff in that you need.
>
> Notice that "line 1" is all about configuring the physical layer, while
> "async 1" is all about configuring the data link layer and network layer.
>
> HTH,
> AQ
> p.s. If all you want is console access, this config should give it to
> you as well.
>
>
> 1 version 12.0
> 2 service timestamps debug uptime
> 3 service timestamps log uptime
> 4 no service password-encryption
> 5 !
> 6 hostname RouterAsyncConfig
> 9 !
> 10 ip subnet-zero
> 11 !
> 22 interface Loopback0
> 23 ip address 1.1.1.1 255.255.255.255
> 24 no ip directed-broadcast
> 25 !
> 26 interface Ethernet0
> 27 no ip address
> 28 no ip directed-broadcast
> 29 no ip route-cache
> 30 no ip mroute-cache
> 31 shutdown
> 32 !
> 33 interface Serial0
> 34 ip address 192.168.10.2 255.255.255.0
> 35 no ip directed-broadcast
> 36 no ip route-cache
> 37 no ip mroute-cache
> 38 no fair-queue
> 39 !
> 40 interface Serial1
> 41 no ip address
> 42 no ip directed-broadcast
> 43 no ip route-cache
> 44 no ip mroute-cache
> 45 shutdown
> 46 no fair-queue
> 47 !
> 48 interface Async1
> 49 no ip address
> 50 no ip directed-broadcast
> 51 encapsulation ppp
> 52 async mode interactive
> 53 peer default ip address pool default
> 54 ppp authentication ms-chap chap pap
> 59 !
> 47 ip local pool Dialup-pool 172.16.20.10 172.16.20.100
> 60 ip classless
> 61 !
> 62 line con 0
> 63 exec-timeout 0 0
> 64 transport input none
> 65 line aux 0
> 66 no exec
> 67 no motd-banner
> 68 no exec-banner
> 69 autoselect ppp
> 70 modem Dialin
> 71 modem autoconfigure type usr_sportster
> 72 transport input all
> 73 stopbits 1
> 74 speed 38400
> 75 flowcontrol hardware
> 76 line vty 0 4
> 77 login
> 78 !
> 79 end
>
>
> At 10:35 AM 1/3/01, Sam wrote:
> >Hello friends
> >
> >I have a modem connected to the AUX port of my router. I am using this
> modem
> >to dial into the router.
> >
> >Now I need to access this modem from the router.
> >What do i need to configure on the router to be able to access the modem
> >from the router itself. ie to be able to configure the modem using the AT
> >command set.
> >Could someone help me out on this.
> >
> >Thanks
> >
> >Sam
> >
> >_________________________________
> >FAQ, list archives, and subscription info:
> >http://www.groupstudy.com/list/cisco.html
> >Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
>
>
> **************************************************
> Adam Quiggle
> Senior Network Engineer
> MCI Worldcom/NOC/BP Amoco
> [EMAIL PROTECTED]
> **************************************************
>
> _________________________________
> FAQ, list archives, and subscription info:
> http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
>
> _________________________________
> FAQ, list archives, and subscription info:
http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
_________________________________
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
