in this case, use the bridge method
bridge 1 protocl ieee
int s 0
no ip add
bridge-group 1
int e 0
no ip add
bridge-group 1
check the command syntax. since i don;t have the
router with me.
Sam
----- Original Message -----
From: "eric^_^" <[EMAIL PROTECTED]>
To: "Sam LI" <[EMAIL PROTECTED]>
Sent: Sunday, January 07, 2001 11:48 AM
Subject: Re: x.25 stock exchange system.
> Hi Sam :
>
> The stock exchange provide not need any ip address in both interface
between stock and
> my router, then how to config our router ?
>
> Thanks !
> eric ^_^
>
>
>
> Sam LI wrote:
>
> > Well
> > to enable the x25 on your router, you need
> >
> > int s 0
> > encap x25
> >
> > if the stock exchange provide ip address, then
> > int s 0
> > encap x25
> > ip address A.B.C.E 255.....
> >
> > and forward it to ethernet interface
> > int e 0
> > ip address X.Y.Z.Z
> >
> > then you can enable any routing protocol that you want
> > like RIP,
> >
> > router Rip
> > network A.B...
> > network X.Y....
> >
> > Sam
> > ----- Original Message -----
> > From: "eric^_^" <[EMAIL PROTECTED]>
> > Newsgroups: groupstudy.cisco
> > To: <[EMAIL PROTECTED]>; "charlesw" <[EMAIL PROTECTED]>
> > Cc: "Fong Kwok Wai Alvin" <[EMAIL PROTECTED]>
> > Sent: Friday, January 05, 2001 12:26 AM
> > Subject: x.25 stock exchange system.
> >
> > > Dear All :
> > >
> > > I need connect to x.25 stock exchange system.
> > > But, I don't know how to connect it with following limit information.
> > > And then, How to config our cisco 2610 recervie the x.25 packet and
> > > forward the
> > > packet to (IP)ethernet interface .
> > > (remark : no any config in router include pvc./ x.121 address..etc/
from
> > > stock operation
> > > staff, ?? PnP ?)
> > >
> > > *
> > > communication line speed : 128 K
> > > comm pro : X.25 on a leased line
> > > re-transmit time-out (t) : 3 sec
> > > re-transmit limit (N2) : 10
> > > frame windows size : 7
> > >
> > > X.25 interface
> > >
> > > x.25 type : x.25(1984)
> > > interface(L2/L3) : DTE
> > > Windows size(default) : 7
> > > packet (default) : 1024
> > >
> > > * x.25 will provide a low level polling mechanism.
> > > This form of poling will allow any disconnection of
> > > information Vendors to be detected by market datafeed system.
> > >
> > > Many thanks ^_^
> > >
> > >
> > >
> > >
> > > _________________________________
> > > FAQ, list archives, and subscription info:
> > http://www.groupstudy.com/list/cisco.html
> > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
> >
> > _________________________________
> > FAQ, list archives, and subscription info:
http://www.groupstudy.com/list/cisco.html
> > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
>
_________________________________
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
