This is a continuation of my earlier posting.
I am doing hands-on lab exercises during my off-class hours. Normally, in
one chapter there 7-9 different router set-ups which involve 3-5 routers and
2-3 switches (2900XL). So after,completing one lab exercise, I have to erase
all the router configurations and do a reload
to have a clean start for the next lab exercise.
As shown below, the router is booting up and there is this "%error opening
tftp:...", this takes a while waiting before I can start configuring the
router. I compared the "show ver" of this router and the other router
(Router-A) which does not exhibit this tftp error and
there are no differences in the image files, configuration registers, etc.
Another router has the same problem and again there are no differences.
But this behavior is not consistent. At one time, after the reload and
rebooting, the router will not show this tftp error and then in another
instance, this tftp error appears.
The command "#no service config" will be effective only for that session but
after clearing up and reloading, this tftp error appears.
Did anybody experience this before? I would highly appreciate if you can
share your solution.
Thanks.
Arthur
PS: As suggested, we performed a password recovery on the routers to remove
the "%tftp error... it also did not work.
------------------------------------------------
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-DO3S-M), Version 12.0(5)T1, RELEASE SOFTWARE
(fc1)
Copyright (c) 1986-1999 by cisco Systems, Inc.
Compiled Tue 17-Aug-99 13:18 by cmong
Image text-base: 0x80008088, data-base: 0x80CB67B0
cisco 2620 (MPC860) processor (revision 0x102) with 26624K/6144K bytes of
memory
.
Processor board ID JAD04390C10 (2949239506)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
2 Low-speed serial(sync/async) network interface(s)
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
%Error opening tftp://255.255.255.255/network-confg (Timed out)
%Error opening tftp://255.255.255.255/cisconet.cfg (Timed out)
SETUP: new interface FastEthernet0/0 placed in "shutdown" state
SETUP: new interface Serial0/0 placed in "shutdown" state
%Error opening tftp://255.255.255.255/network-confg (Timed out)
%Error opening tftp://255.255.255.255/cisconet.cfg (Timed out)
%Error opening tftp://255.255.255.255/router-confg (Timed out)
%Error opening tftp://255.255.255.255/ciscortr.cfg (Timed out)
Press RETURN to get started!
00:02:42: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-DO3S-M), Version 12.0(5)T1, RELEASE SOFTWARE
(fc
1)
Copyright (c) 1986-1999 by cisco Systems, Inc.
Compiled Tue 17-Aug-99 13:18 by cmong
Router>
Router>en
Router#show ver
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-DO3S-M), Version 12.0(5)T1, RELEASE SOFTWARE
(fc
1)
Copyright (c) 1986-1999 by cisco Systems, Inc.
Compiled Tue 17-Aug-99 13:18 by cmong
Image text-base: 0x80008088, data-base: 0x80CB67B0
ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
Router uptime is 2 minutes
System returned to ROM by power-on
System image file is "flash:c2600-do3s-mz.120-5.T1"
cisco 2620 (MPC860) processor (revision 0x102) with 26624K/6144K bytes of
memory
.
Processor board ID JAD04390C10 (2949239506)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
2 Low-speed serial(sync/async) network interface(s)
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
Router#
----------------------------------------
Router-A has no TFTP error problem.
----------------------------------------
Router-A#show ver
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-DO3S-M), Version 12.0(5)T1, RELEASE SOFTWARE
(fc
1)
Copyright (c) 1986-1999 by cisco Systems, Inc.
Compiled Tue 17-Aug-99 13:18 by cmong
Image text-base: 0x80008088, data-base: 0x80CB67B0
ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
Router-A uptime is 10 minutes
System returned to ROM by power-on
System image file is "flash:c2600-do3s-mz.120-5.T1"
cisco 2621 (MPC860) processor (revision 0x102) with 26624K/6144K bytes of
memory
.
Processor board ID JAD04410BHU (2693993419)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
Basic Rate ISDN software, Version 1.1.
2 FastEthernet/IEEE 802.3 interface(s)
2 Serial(sync/async) network interface(s)
1 ISDN Basic Rate interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
Router-A#
_________________________________________________________________
Get your FREE download of MSN Explorer at http://explorer.msn.com
_________________________________
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
