but the ip addresses of pc is the same subnet of the fastethernet 0 of 3640! so the router will think that the ip addresses is connected directly to it,when after u config the router: ip route 1.1.1.2 255.255.255.255 dialer0 u use "show ip route",u can't see the route to 1.1.1.2/32,because the router think that the pc is connected directly to it "MihaiDumitru" wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > Configure several dialer interfaces (one for each NT box) on the 3640. > Don't forget to configure ms-chap authentication and dialer strings on > those interfaces. > > Create or modify the access list(s) as needed, that one provided below > is the most general. > > Something like this: > > chat-script dial-up ABORT ERROR ABORT BUSY ABORT "NO ANSWER" "" "ATZ" OK > "ATDP\T > " TIMEOUT 120 CONNECT \c > ! > ! > ! > interface Loopback2 > ip address 1.2.3.1 255.255.255.255 > no ip directed-broadcast > ! > interface Async40 > no ip address > encapsulation ppp > dialer in-band > dialer pool-member 1 > no cdp enable > ! > interface Dialer2 > ip unnumbered Loopback2 > encapsulation ppp > dialer pool 1 > dialer idle-timeout 600 > dialer string 1234567890 > dialer hold-queue 50 > dialer-group 1 > no cdp enable > ppp authentication ms-chap callin > ppp chap hostname c3640 > ppp chap password 7 XXXXXXXX > ! > ! here you define dialer interfaces for each NT box > ! > ip route 1.2.3.2 255.255.255.255 Dialer2 > ! > ! ip route 1.2.3.3 255.255.255.255 Dialer3 > ! etc > ! > access-list 101 deny icmp any any > access-list 101 deny ip any host 255.255.255.255 > access-list 101 permit ip any any > dialer-list 1 protocol ip list 101 > ! > line 40 > script dialer dial-up > modem InOut > modem autoconfigure type usr_courier > transport input all > stopbits 1 > speed 115200 > flowcontrol hardware > ! > > Configure (R)RAS on the NT boxes to allow incoming calls. > > > leo wrote: > > > > Remote Site(Server) > > | > > |DDN(ppp)/FR > > | > > | > > > > |-------| > > | 3640 | > > |-------|1.2.3.1/24 > > | | pstn(ddr) > > | | > > |----| |----| > > |pc01| |pc02| ......pc09 > > |----| |----| > > 1.2.3.2 1.2.3.3 ......1.2.3.10 > > > > As the above picture,the router connects 9 PCs via ddr(pstn) and > > connect remote via DDN/FR. > > now,pc has its own statical ip address,its OS is nt/2000,when it wants > > to send data to remote site,it can dial in the 3640.but what i want > is,when > > the remote or 3640 wants to send data to one of the 9 PCs,what must I > config > > in 3640 and the PCs? > > thanx! > > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > -- > > > Mihai Dumitru > Systems Engineer, ROMSYS SA > > tel: +40 1 2300810, mobile: +40 92 764287 > fax: +40 1 2300815 > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=472&t=456 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
