Yes i also have used an access-list to prevent eigrp
to initiate call, and it dials on a ping event, as
shown by the 'deb dialer events'
shoaib
--- Albert Lu wrote:
> Try using debug dialer events to see if the dialing
> actually takes place
> when you ping. If the dialer doesn't come up, then
> it could be a dialer
> problem. If it does come up, and dialing fails, then
> it could be an isdn
> problem.
>
> Albert
>
> > -----Original Message-----
> > From: Shoaib Waqar [mailto:[EMAIL PROTECTED]]
> > Sent: Tuesday, 1 May 2001 9:54
> > To: Albert lu
> > Cc: [EMAIL PROTECTED]
> > Subject: RE: ISDN BRI up but does not ping
> [7:2712]
> >
> >
> > I have tried dialer profiles, legacy DDR with
> dialer
> > mao statement and with floating static route too,
> but
> > still same result, could not ping the neighbor.
> > Offcourse there is a dialer-list statement to
> initiate
> > call:
> >
> > dialer-list 1 protocol ip permit
> >
> > Shoaib
> >
> >
> >
> > --- Albert Lu wrote:
> > > I personally think that using dialer profiles
> are
> > > better than hard coding
> > > the interface. It is also true that there is no
> > > dialer-list command to dial
> > > for interesting traffic, and you don't have a
> route
> > > to use the bri interface
> > > so it wouldn't know when to dial.
> > >
> > > Wouldn't you need a dialer map command for
> > > interfaces, rather than specify
> > > dialer string?
> > >
> > > Albert
> > >
> > > > -----Original Message-----
> > > > From: [EMAIL PROTECTED]
> > > [mailto:[EMAIL PROTECTED]]On Behalf Of
> > > > Shoaib Waqar
> > > > Sent: Tuesday, 1 May 2001 6:15
> > > > To: [EMAIL PROTECTED]
> > > > Subject: ISDN BRI up but does not ping
> [7:2712]
> > > >
> > > >
> > > > I am getting trouble in ISDN bri link. I have
> a
> > > > Central site Router 3640 with 12.1.8 IP/IPX
> plus
> > > IOS.
> > > > the route has 4 port BRI module. The remote
> site
> > > is
> > > > having 2503, all u know that it has 1 port
> BRI.
> > > remote
> > > > site is running 11.2.1 version of IOS. The
> call is
> > > > placed using simple DDR commands as:
> > > >
> > > > Cisco 3640 Router
> > > > =================
> > > > Int bri 2/0
> > > > ip add 130.1.1.1 255.255.255.0
> > > > encap ppp
> > > > dialer idle-timeout 300
> > > > dialer fast-idle 300
> > > > dialer string xxxxxxxx
> > > > dialer-group 1
> > > >
> > > > Remote site (2503):
> > > > ===================
> > > >
> > > > Int bri 0
> > > > ip add 130.1.1.2 255.255.255.0
> > > > encap ppp
> > > > dialer idle-timeout 300
> > > > dialer fast-idle 300
> > > >
> > > > In this scenario, a/c to customer need, the
> > > central
> > > > site is placing call.When the call has placed,
> and
> > > we
> > > > see the debug output, it shows all the debug
> of
> > > ppp
> > > > negotiations and ISDN events as correct, with
> the
> > > > install route at the end. When i run 'show
> isdn
> > > > status' it shows me all layers up with one
> active
> > > > layer 3 call also. Also 'show isdn active'
> gives
> > > me
> > > > successful call to remote site. So nothing
> seems
> > > to be
> > > > wrong with config. THE problem is that after
> > > > connectivity when i try to ping from central
> site
> > > the
> > > > remote site ip address, it times out. I took
> the
> > > 'show
> > > > ip route', and it gives me only connected
> routes
> > > but
> > > > dont show me the remote LAN network address of
> > > each
> > > > site which it should give as i m running EIGRP
> at
> > > both
> > > > sites. The primary link is working correctly
> as i
> > > have
> > > > an SCPC 128K link between the two sites as
> well
> > > and
> > > > showing correct routes. The switch type in
> > > pakistan
> > > > normally we use is basic-net3 (SIEMENS
> switch).
> > > Can
> > > > anyone plzz help me, where is the issue?? i
> have
> > > tried
> > > > everything, dialer profiles and all. but
> nothing
> > > seems
> > > > to be working, i cant ping the other side thru
> > > BRI.
> > > >
> > > > Shoaib
> > > > CCNP,MCSE
> > > >
> > > >
> > > >
> > > >
> __________________________________________________
> > > > Do You Yahoo!?
> > > > Yahoo! Auctions - buy the things you want at
> great
> > > prices
> > > > http://auctions.yahoo.com/
> > > > FAQ, list archives, and subscription info:
> > > > http://www.groupstudy.com/list/cisco.html
> > > > Report misconduct and Nondisclosure violations
> to
> > > [EMAIL PROTECTED]
> > >
> >
> >
> > __________________________________________________
> > Do You Yahoo!?
> > Yahoo! Auctions - buy the things you want at great
> prices
> > http://auctions.yahoo.com/
>
__________________________________________________
Do You Yahoo!?
Yahoo! Auctions - buy the things you want at great prices
http://auctions.yahoo.com/
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=2733&t=2712
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
