here is the show int:
Router#sh int s0/0
Serial0/0 is down, line protocol is down
Hardware is PQUICC with Fractional T1 CSU/DSU
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Keepalive set (10 sec)
Last input never, output never, output hang never
Last clearing of "show interface" counters 00:21:48
Input queue: 0/75/0 (size/max/drops); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/0/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 43 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
DCD=down DSR=up DTR=up RTS=up CTS=down
Neil
""Neil Schneider"" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Pinouts are 1-4 and 2-5 crossed. leds show alarm on both cards. They are
> definately not shutdown. Show int results will have to wait. I just
tried
> to update the ios on one router and now it is not booting correctly. No
> interfaces are being seen. (makes it hard to do a tftp download)
>
> Neil Schneider
>
>
> ----- Original Message -----
> From: "Jim Brown"
> To: "'Neil Schneider'" ;
> Sent: Tuesday, May 08, 2001 12:42 PM
> Subject: RE: back-to-back t1 with wic-1dsu-t1? [7:3633]
>
>
> > I believe clock source internal on one of the cards is all you need to
> bring
> > them up. Please post the 'show interface' results from both routers and
> the
> > related configs.
> >
> > What pinouts did you use for the cross-over cable?
> >
> > What LEDs are illuminated on the cards with the cable plugged in?
> >
> > Are you sure the interfaces are not in a shutdown state?
> >
> > -----Original Message-----
> > From: Neil Schneider [mailto:[EMAIL PROTECTED]]
> > Sent: Tuesday, May 08, 2001 10:47 AM
> > To: [EMAIL PROTECTED]
> > Subject: back-to-back t1 with wic-1dsu-t1? [7:3633]
> >
> >
> > I am trying to set up 2 t1 wics back to back to simulate a t1 wan
> > connection. I have a T1 crossover cable, clock source is internal on
one
> > card, but I get nothing, down and down. Is anyone doing this and
willing
> to
> > share a configuration? Or give me a hint as to what may be wrong
> >
> > Thanks
> >
> > Neil Schneider
> > CCNP CCSI (setting up a CCIE lab)
> > FAQ, list archives, and subscription info:
> > http://www.groupstudy.com/list/cisco.html
> > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
> FAQ, list archives, and subscription info:
http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=3670&t=3633
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
