Hi all,
I am getting the following error when I boot up the 801 router.
%Error opening tftp://255.255.255.255/network-confg (Socket error)
%Error opening tftp://255.255.255.255/cisconet.cfg (Socket error)
%Error opening tftp://255.255.255.255/routera-confg (Socket error)
%Error opening tftp://255.255.255.255/routera.cfg (Socket error)
The output of the 801 boot seqence and config is as given below.
Please help.
TinyROM version 1.4(1)
19:38 11/07/00
Copyright (c) 1998-2000 by cisco Systems, Inc.
All rights reserved.
POST ............ OK. 4MB DRAM, 8MB Flash.
Accessing flash:c800-y6-mw.121-3.XG2
Booting "c800-y6-mw.121-3.XG2" ...,
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) C800 Software (C800-Y6-MW), Version 12.1(3)XG2, EARLY
DEPLOYMENT RELEASE SOFTWARE (fc1)
TAC:Home:SW:IOS:Specials for info
Copyright (c) 1986-2000 by cisco Systems, Inc.
Compiled Mon 13-Nov-00 17:27 by detang
Image text-base: 0x000EE000, data-base: 0x00654000
Cisco C801 (MPC850) processor (revision 1) with 43464K bytes of virtual
memory.
Processor board ID JAD05030E7A
CPU part number 0x2101
Bridging software.
Basic Rate ISDN software, Version 1.1.
1 Ethernet/IEEE 802.3 interface(s)
1 ISDN Basic Rate interface(s)
4M bytes of physical memory (DRAM)
8K bytes of non-volatile configuration memory
8M bytes of flash on board (4M from flash card)
%Error opening tftp://255.255.255.255/network-confg (Socket error)
%Error opening tftp://255.255.255.255/cisconet.cfg (Socket error)
%Error opening tftp://255.255.255.255/routera-confg (Socket error)
%Error opening tftp://255.255.255.255/routera.cfg (Socket error)
Press RETURN to get started!
00:00:21: %LINK-3-UPDOWN: Interface Ethernet0, changed state to up
00:00:22: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0,
changed state to up
00:00:25: %LINK-5-CHANGED: Interface BRI0, changed state to
administratively down
00:00:25: %SYS-5-CONFIG_I: Configured from memory by console
00:00:26: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0, changed
state to down
00:00:26: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) C800 Software (C800-Y6-MW), Version 12.1(3)XG2, EARLY
DEPLOYMENT RELEASE SOFTWARE (fc1)
TAC:Home:SW:IOS:Specials for info
Copyright (c) 1986-2000 by cisco Systems, Inc.
Compiled Mon 13-Nov-00 17:27 by detang
00:00:26: %LINK-5-CHANGED: Interface Ethernet0, changed state to
administratively down
00:00:27: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0,
changed state to down
RouterA#sh run
Building configuration...
Current configuration:
!
version 12.1
service config
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname RouterA
!
boot config flash:nvram
enable secret 5 $1$nTbn$GQVW3zqE.sEBllYS0y6Bt0
enable password cisco
!
ip subnet-zero
!
isdn switch-type basic-net3
!
interface Ethernet0
no ip address
shutdown
no cdp enable
interface BRI0
no ip address
shutdown
isdn switch-type basic-net3
no cdp enable
no ip http server
ip classless
dialer-list 1 protocol ip permit
dialer-list 1 protocol ipx permit
bridge 1 protocol dec
line con 0
exec-timeout 0 0
stopbits 1
line vty 0 4
password cisco
login
no rcapi server
end
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=8826&t=8826
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
