Here is the exact debug output.
1d18h: ISDN Se0:15: RX CALL_PROC pd = 8 callref = 0x8061
1d18h: Channel ID i = 0xA9838E
1d18h: ISDN Se0:15: TX -> CONNECT pd = 8 callref = 0x8061
1d18h: Channel ID i = 0xA9838E
1d18h: Se0:13 DDR: dialer protocol up
1d18h: ISDN Se0:15: RX DISCONNECT pd = 8 callref = 0x8061
1d18h: Cause i = 0x8090 - Normal call clearing
1d18h: ISDN Se0:15: RX RELEASE_COMP pd = 8 callref = 0x8061
""Mihai"" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Hello,
>
> I have a problem seting a voip connection between 2 AS5300. They are both
> linked to E1 trunks, ISDN primary-net5 signalling.
>
> Here is a the configuration:
>
> ROUTER A:
>
> controller E1 0
> framing NO-CRC4
> clock source line primary
> pri-group timeslots 1-31
> !
> interface Ethernet0
> ip address 192.168.101.1 255.255.255.0
>
> interface Serial0:15
> no ip address
> ip mroute-cache
> no logging event link-status
> isdn switch-type primary-net5
> isdn overlap-receiving
> isdn incoming-voice data 64
> isdn T310 60000
> no cdp enable
> !
> voice-port 0:D
> cptone CZ
> !
> dial-peer voice 1 voip
> destination-pattern 1T
> session target ipv4:192.168.101.2
> !
> gateway
> !
> !
>
> ROUTER B:
>
> controller E1 0
> framing NO-CRC4
> clock source line primary
> pri-group timeslots 1-31
> !
> interface Ethernet0
> ip address 192.168.101.2 255.255.255.0
>
> interface Serial0:15
> no ip address
> ip mroute-cache
> no logging event link-status
> isdn switch-type primary-net5
> isdn overlap-receiving
> isdn incoming-voice data 64
> isdn T310 60000
> no cdp enable
> !
> voice-port 0:D
> cptone CZ
> !
> dial-peer voice 1 pots
> destination-pattern 1T
> port 0:D
> !
> gateway
> !
> !
>
>
> The call never reach the Router B and here is the debug output from Router
> A:
>
> 1d18h: ISDN Se0:15: RX CALL_PROC pd = 8 callref = 0x8061
> 1d18h: Channel ID i = 0xA9838E
> 1d18h: ISDN Se0:15: TX -> CONNECT pd = 8 callref = 0x8061
> 1d18h: Channel ID i = 0xA9838E
> 1d18h: Se0:13 DDR: dialer protocol up
> 1d18h: ISDN Se0:15: RX DISCONNECT pd = 8 callref = 0x8061
> 1d18h: Cause i = 0x8090 - Normal call clearing
> 1d18h: ISDN Se0:15: RX RELEASE_COMP pd = 8 callref = 0x8061
>
>
> Where you see the Medusa# prompt the call connected and stays connected
for
> a few seconds. Any ideas ?
>
> Regards,
> Mihai
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=16356&t=16355
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
