Frederick
I've never worked with less than 30 channels when configuring VoIP and E1s,
but here's some config's for the D channel and the controller. The problem
could be the busy-out command what's it being used for?
cheers Pat
interface Serial1/0:15
no ip address
no logging event link-status
isdn switch-type primary-net5
isdn incoming-voice modem
isdn sending-complete
fair-queue 64 256 0
no cdp enable
controller E1 1/0
clock source line primary
line-termination 75-ohm
pri-group timeslots 1-31
""VAN RYCKEGHEM Fridiric"" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Hello,
>
> I have a Cisco gtw ( 2610 with an NM-HDV using a EVWIC-1MFTE1) to the
> PSTN.
>
> the PRI is configured as follows :
>
> controller E1 1/0
> framing NO-CRC4
> pri-group timeslots 1-12,16
> ds0 busyout 13-31
> description vers PRA BGC
>
> I only use the timeslots 1-12 because I only have 12 DSP on the card.
>
> the problem is that when a call from the PSTN arrives on a channel >=
> 13, it is not working
>
> 2d01h: ISDN Se1/0:15: RX RELEASE_COMP pd = 8 callref = 0x802D
> 2d01h: Cause i = 0x80AC18 - Requested circuit/channel not
> available
>
>
> if I configure the 1-31 timeslots on the E1, I have this error at
> the creation of the timeslots :
>
>
> oslo-r1(config-controller)#pri-group timeslots 1-31
> oslo-r1(config-controller)#
> 2d01h: %LINK-3-UPDOWN: Interface ISDN-VOICE 1/0:15(1), changed state to
> up
> 2d01h: %LINK-3-UPDOWN: Interface ISDN-VOICE 1/0:15(2), changed state to
> up
> 2d01h: %LINK-3-UPDOWN: Interface ISDN-VOICE 1/0:15(3), changed state to
> up
> 2d01h: %LINK-3-UPDOWN: Interface ISDN-VOICE 1/0:15(4), changed state to
> up
> 2d01h: %LINK-3-UPDOWN: Interface ISDN-VOICE 1/0:15(5), changed state to
> up
> 2d01h: %LINK-3-UPDOWN: Interface ISDN-VOICE 1/0:15(6), changed state to
> up
> 2d01h: %LINK-3-UPDOWN: Interface ISDN-VOICE 1/0:15(7), changed state to
> up
> 2d01h: %LINK-3-UPDOWN: Interface ISDN-VOICE 1/0:15(8), changed state to
> up
> 2d01h: %LINK-3-UPDOWN: Interface ISDN-VOICE 1/0:15(9), changed state to
> up
> 2d01h: %LINK-3-UPDOWN: Interface ISDN-VOICE 1/0:15(10), changed state to
> up
> 2d01h: %LINK-3-UPDOWN: Interface ISDN-VOICE 1/0:15(11), changed state to
> up
> 2d01h: %LINK-3-UPDOWN: Interface ISDN-VOICE 1/0:15(12), changed state to
> upvnm_dsprm_find_free_real_sig_channel: No free channels.
> 2d01h: %DSPRM-3-INSUFFICIENT: Insufficient DSP resources for timeslot 13
> on port 1/0:15vnm_dsprm_find_free_real_sig_channel: No free channels.
> 2d01h: %DSPRM-3-INSUFFICIENT: Insufficient DSP resources for timeslot 14
> on port 1/0:15vnm_dsprm_find_free_real_sig_channel: No free channels.
> 2d01h: %DSPRM-3-INSUFFICIENT: Insufficient DSP resources for timeslot 15
> on port 1/0:15vnm_dsprm_find_free_real_sig_channel: No free channels.
> 2d01h: %DSPRM-3-INSUFFICIENT: Insufficient DSP resources for timeslot 17
> on port 1/0:15vnm_dsprm_find_free_real_sig_channel: No free channels.
> 2d01h: %DSPRM-3-INSUFFICIENT: Insufficient DSP resources for timeslot 18
> on port 1/0:15vnm_dsprm_find_free_real_sig_channel: No free channels.
> 2d01h: %DSPRM-3-INSUFFICIENT: Insufficient DSP resources for timeslot 19
> on port 1/0:15vnm_dsprm_find_free_real_sig_channel: No free channels.
> 2d01h: %DSPRM-3-INSUFFICIENT: Insufficient DSP resources for timeslot 20
> on port 1/0:15vnm_dsprm_find_free_real_sig_channel: No free channels.
> 2d01h: %DSPRM-3-INSUFFICIENT: Insufficient DSP resources for timeslot 21
> on port 1/0:15vnm_dsprm_find_free_real_sig_channel: No free channels.
> 2d01h: %DSPRM-3-INSUFFICIENT: Insufficient DSP resources for timeslot 22
> on port 1/0:15vnm_dsprm_find_free_real_sig_channel: No free channels.
> 2d01h: %DSPRM-3-INSUFFICIENT: Insufficient DSP resources for timeslot 23
> on port 1/0:15vnm_dsprm_find_free_real_sig_channel: No free channels.
> 2d01h: %DSPRM-3-INSUFFICIENT: Insufficient DSP resources for timeslot 24
> on port 1/0:15vnm_dsprm_find_free_real_sig_channel: No free channels.
> 2d01h: %DSPRM-3-INSUFFICIENT: Insufficient DSP resources for timeslot 25
> on port 1/0:15vnm_dsprm_find_free_real_sig_channel: No free channels.
> 2d01h: %DSPRM-3-INSUFFICIENT: Insufficient DSP resources for timeslot 26
> on port 1/0:15vnm_dsprm_find_free_real_sig_channel: No free channels.
> 2d01h: %DSPRM-3-INSUFFICIENT: Insufficient DSP resources for timeslot 27
> on port 1/0:15vnm_dsprm_find_free_real_sig_channel: No free channels.
> 2d01h: %DSPRM-3-INSUFFICIENT: Insufficient DSP resources for timeslot 28
> on port 1/0:15vnm_dsprm_find_free_real_sig_channel: No free channels.
> 2d01h: %DSPRM-3-INSUFFICIENT: Insufficient DSP resources for timeslot 29
> on port 1/0:15vnm_dsprm_find_free_real_sig_channel: No free channels.
> 2d01h: %DSPRM-3-INSUFFICIENT: Insufficient DSP resources for timeslot 30
> on port 1/0:15vnm_dsprm_find_free_real_sig_channel: No free channels.
> 2d01h: %DSPRM-3-INSUFFICIENT: Insufficient DSP resources for timeslot 31
> on port 1/0:1
>
>
> and when the outside call comes on a channel >= 13, I have this
> error
>
> 2d01h: ISDN Se1/0:15: RX RELEASE_COMP pd = 8 callref = 0x802E
> 2d01h: Cause i = 0x80AF - Resource unavailable, un d
>
>
>
> So My question is, is there a way to use the DSP like a pool of DSP
> rather than associating the first DSP to the first channel, the
> second DSP to the second channel and so on ... ?
>
> So I can use my 30 channels of my E1 with 12 DSP, according no
> importance to the channel beeing used.
>
> Thks
>
> Frederic Van Ryckeghem
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=17853&t=17851
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
