----- Original Message ----- From: "Rik Guyler" To: Sent: Friday, September 07, 2001 11:14 PM Subject: RE: FR question - Configuring Fractional T1 on the WIC-1DSU-T1 [7:19091] > However, it appears that Ole wants to (correct me if I'm wrong) limit the > bandwidth per DLCI. Is this true? If that's the case, unfortunately there > is no way to do this on the router. nah, that's not what he wants, nor asked for. His provider has given him a 768k access rate, and he thought he has to set up his T-1 WIC channelized for each DLCI. Chuck set him straight on that one, although I understand the confusion. And I'll do some research, but with newer versions of IOS one *might* now be able to limit bandwidth per DLCI. > > When you order a FR circuit, you are typically ordering a T1 for layer 1 so > you really are just getting 1 "pipe" capable of flowing 768k. The DLCIs > converge into this pipe in a logical fashion, not a physical one, hence the > layer 2 stuff (FR encapsulation) needed at this point. Same point Chuck made > > --- > Rik Guyler > > -----Original Message----- > From: Chuck Larrieu [mailto:[EMAIL PROTECTED]] > Sent: Friday, September 07, 2001 11:21 PM > To: [EMAIL PROTECTED] > Subject: RE: FR question - Configuring Fractional T1 on the WIC-1DSU-T1 > [7:19081] > > > Ole, my man, you are trying to outsmart yourself, and you're a pretty smart > guy ;-> > > Your T1 module is for the telco interface only. You purchased 768K, it > appears. Your DLCI's / PVC's will share that 768K with no further layer 1 > actions on your part > > once you have properly configured the layer one stuff - the timeslots and > B8ZS and ESF and yellow alarm and loopback and clock source, you are done > with the service module. > > All that remains is assigning the DLCI's to the appropriate subinterface, > and IP addressing for the PVC's, and you are on your way. > > Chuck > > -----Original Message----- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Ole Drews Jensen > Sent: Friday, September 07, 2001 3:11 PM > To: [EMAIL PROTECTED] > Subject: FR question - Configuring Fractional T1 on the WIC-1DSU-T1 > [7:19057] > > > I am now on unknown territory, where no man in my shoes has walked before. > > I have a Frame Relay scenario being setup, and my host router has just > received the green light from the provider. > > The Frame Relay host uses 12 channels, and connects on three PVC's to three > branch offices, each with 4 channels. > > I searched and found the answer on how to setup the channels on cisco's > site: > > router(config-if)#service-module t1 timeslots 1-12 > > but will I have to do that for my three sub interfaces also? > > Example: > > router(config)#int s0/0 > router(config-if)#service-module t1 timeslots 1-12 > > router(config-if)#int s0/0.101 point-to-point > router(config-subif)#frame-relay interface-dlci 101 > router(config-subif)#service-module t1 timeslots 1-4 > router(config-subif)#int s0/0.102 point-to-point > router(config-subif)#frame-relay interface-dlci 102 > router(config-subif)#service-module t1 timeslots 5-8 > router(config-subif)#int s0/0.103 point-to-point > router(config-subif)#frame-relay interface-dlci 103 > router(config-subif)#service-module t1 timeslots 9-12 > > Thanks and have a great weekend, > > Ole > > ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ > Ole Drews Jensen > Systems Network Manager > CCNA, MCSE, MCP+I > RWR Enterprises, Inc. > [EMAIL PROTECTED] > ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ > http://www.RouterChief.com > ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ > NEED A JOB ??? > http://www.oledrews.com/job > ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ _________________________________________________________ Do You Yahoo!? Get your free @yahoo.com address at http://mail.yahoo.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=19095&t=19095 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
