Glad to hear you figured it out! Silly Routing... It'll get ya every time :)
-Mark Odette II StellarConnection Services -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of Chamak Sent: Thursday, October 18, 2001 9:54 AM To: [EMAIL PROTECTED] Subject: Re: VoIP Installation Issue [7:23254] What a silly thing I was doing.... I gave enable IP routing and it started working. Mukul ""Mark Odette II"" wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > Chamak, > I interpret that you have the following: > 2 1751's with (1)2FXS VIC and (1)2FXO VIC in each of this 1751's. > > You say that you can Pick up a standard POTS phone (analogue handset) that > is plugged into port 1 of the first 1751's FXS VIC and dial your dial-plan > to port 2 of same FXS VIC on same router. You say you can also do the same > thing plugging a standard POTS (analogue phone) line into either port of the > FXO VIC on the same 1751, and dial an outside line. > > Connecting the two 1751's up to a hub/switch or even a cross-over cable > between the two 10/100 interfaces and creating dial-peers between the two > routers, and then dialing from FXS port on R1 to R2 FXS port yields invalid > results. > > The next step to do is perform all the dial tests for the second router that > you did with the first (calling from port 1 FXS to Port 2 FXS, Port 1 or 2 > of FXS to Port 1 or 2 of FXO on same router). > > If you get the same exact results as the first router, then verify the same > version of IOS is running on both Routers. > > Aside from that, I'd call Cisco TAC. > > Creating the Dial-Peers for VoIP are pretty straight forward, and you have > many examples on the Cisco web site to choose from. The basic dial-peer > config is only 2 lines, 3 at max if you modify the default codec. This > assumes you are dialing from router A to Router B over the 10/100BT network > interface and the two routers are on the same Hub/Switch and the routers are > on the same subnet for simplicity of testing. > > I hope this is of some help. > > -Mark Odette II > StellarConnection Services > -----Original Message----- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Chamak > Sent: Wednesday, October 17, 2001 5:53 PM > To: [EMAIL PROTECTED] > Subject: Re: VoIP Installation Issue [7:23254] > > > Thanks Marc, > But I have got these router just 3 days back. Can you advice how can we make > sure that it's VIC problem and not the config. > > > Mukul > > > ""Mark Odette II"" wrote in message > news:[EMAIL PROTECTED]... > > Chamak- I can't recall the Cisco Bugtrak ID, but what you describe sounds > > verry familiar to a problem they posted about the Voice WIC being > defective. > > You might see about calling Cisco TAC for support. If you bought the > router > > less than a year ago, you might get your Voice WIC replaced under > warranty. > > > > HTHs! > > Mark Odette II > > StellarConnection Services > > > > -----Original Message----- > > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > > Chamak > > Sent: Wednesday, October 17, 2001 9:39 AM > > To: [EMAIL PROTECTED] > > Subject: VoIP Installation Issue [7:23254] > > > > > > hii All, > > > > I am creating a test circuit using 2 1751 routers with FXS and FXO port. > > > > My Scenario for test is > > > > Phone ----> ROUTER1 ========LAN=========ROUTER2-------->Phone > > > > I do not have WAN interfaces, just to try I am using the Lan port. > > LAN port on router 1 = 192.168.1.100 > > LAN port on Router 2 = 192.168.1.200 > > > > As for now. > > 1. I am able to place call on the same ports of router ( ex., Port 1/0 and > > 1/1 of FXS) > > 2. Also I am able to use PSTN line on the same router that is Call from > Port > > 1/0 (FXS) to Port 2/0 (FXO). > > > > but, > > When I configured both the routers and created VoIP dial-peers. When I > dial > > from the phone on router1 I cannot hear the progress tone, but the phone > on > > router2 rings. Moreover when phone on router 2 is picked up I cannot see > any > > significant activity on the etherner interface and No Voice comes. > > Surprisingly, If the Phone2 is busy then I get the busy tone., > > > > Can you please help me setting the above scenario. I am looking forward to > > hear from you all ! > > > > > > Mukul Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=23420&t=23254 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
