What is the question. Looks like the only issue is different destinations on the echo reply. Could you send the configs
----- Original Message ----- From: "Timothy Ouellette" To: Sent: Saturday, November 10, 2001 9:17 PM Subject: Basic RIP problem - am I missing something? [7:25787] > This should have been a simple rip setup that I was going to use to play > around with offset-lists and stuff but it's not functioning the way I > thought it would. Can you guys/gals have a look! > > ethernetA - Router A ===HDLC=== Router B - ethernetB > > router a is connected to router b with 2 serial int's running rip. The > address of 10.1.1.1 is the ethernet of routerA and i'm consoled into > router B. I have no ip route-cache on all the serial interface's in > this setup. I've also done a "sh ip cache" just to make sure. > > lola#sh ip route > Gateway of last resort is not set > > 10.0.0.0/24 is subnetted, 4 subnets > C 10.1.3.0 is directly connected, Ethernet0 > C 10.1.2.0 is directly connected, Serial0 > R 10.1.1.0 [120/1] via 10.1.2.1, 00:00:05, Serial0 > [120/1] via 10.1.4.1, 00:00:05, Serial1 > C 10.1.4.0 is directly connected, Serial1 > lola# > > lola#ping 10.1.1.1 > > Type escape sequence to abort. > Sending 5, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds: > !!!!! > Success rate is 100 percent (5/5), round-trip min/avg/max = 12/12/12 ms > lola# > 03:45:09: ICMP: echo reply rcvd, src 10.1.1.1, dst 10.1.2.2 > 03:45:09: ICMP: echo reply rcvd, src 10.1.1.1, dst 10.1.2.2 > 03:45:09: ICMP: echo reply rcvd, src 10.1.1.1, dst 10.1.2.2 > 03:45:09: ICMP: echo reply rcvd, src 10.1.1.1, dst 10.1.2.2 > 03:45:09: ICMP: echo reply rcvd, src 10.1.1.1, dst 10.1.2.2 > lola#ping 10.1.1.1 > > Type escape sequence to abort. > Sending 5, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds: > !!!!! > Success rate is 100 percent (5/5), round-trip min/avg/max = 12/12/12 ms > lola# > 03:45:13: ICMP: echo reply rcvd, src 10.1.1.1, dst 10.1.4.2 > 03:45:13: ICMP: echo reply rcvd, src 10.1.1.1, dst 10.1.4.2 > 03:45:13: ICMP: echo reply rcvd, src 10.1.1.1, dst 10.1.4.2 > 03:45:13: ICMP: echo reply rcvd, src 10.1.1.1, dst 10.1.4.2 > 03:45:13: ICMP: echo reply rcvd, src 10.1.1.1, dst 10.1.4.2 > lola#ping 10.1.1.1 > > Type escape sequence to abort. > Sending 5, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds: > !!!!! > Success rate is 100 percent (5/5), round-trip min/avg/max = 12/12/12 ms > lola# > 03:45:16: ICMP: echo reply rcvd, src 10.1.1.1, dst 10.1.2.2 > 03:45:16: ICMP: echo reply rcvd, src 10.1.1.1, dst 10.1.2.2 > 03:45:16: ICMP: echo reply rcvd, src 10.1.1.1, dst 10.1.2.2 > 03:45:16: ICMP: echo reply rcvd, src 10.1.1.1, dst 10.1.2.2 > 03:45:16: ICMP: echo reply rcvd, src 10.1.1.1, dst 10.1.2.2 Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=25930&t=25787 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
