> Dear CCIEs, > > I failed in the CCIE written exam today and, I recall some questions here > but can't find the correct answer. Do please help me figure out the correct > answer and give me your explain. Great thanks! >
Wow, that is a lot of questions, and it clearly indicates that you were not ready for the CCIE Written exam. Where did you LOOK for the correct answer? May I politely suggest that you study the information on Cisco more carefully, then provide your own answers to these questions? Those of us who have passed had to learn the answers by reading and then remembering the information. Almost all of the answers that you are requestion can be found at www.cisco.com so please do your studying. Other members have informed you by asking these questions, you are breaking the Cisco Non-Disclosure Agreement that you signed before you took the exam (non-disclosure means, don't tell anyone what the questions or answers are on the exam). You should be concerned that if you are caught violating this non-disclosure agreement, you will be barred from taking the Written Exam. Are the answers to these questions really worth the suspension? Also, CCIE's are usually very independent and know how to do research on a subject before asking questions for help. You should start your training in that manner - do the research FIRST, and then when you can't find the answer, ask us here on the list. PS Many of us know the answers to these questions, and the answers are easily found in the Cisco documentation and in the books that are suggested reading material for the CCIE Written exam. > 1.. In a token ring environment, what is allowed regarding early token > release? > > > A. More than one token can circulate the ring at any given > time, but only one data frame is allowed. > > B. More than one data frame can circulate the ring at any > given time, but only one token is allowed. > > C. More than one data frame and more than one token can > circulate the ring at any given time. > > D. A station releases a free token after stripping the frame > from the ring > > E. A station can transmit early without waiting for a token > to be released from its neighbor. > > > > 2. What is the best description of poison reverse? > > > > A. It is a procedure used by OSPF to remove a network from > the OSPF area. > > B. Once a connection disappears, the router advertising the > bad network will send an update from this network indicating an infinite > cost. > > C. The specific network is not sent out again on the > interface it was received on. > > The network is sent back out on the interface it was received on, but with a > metric of one more than the metric in the receive update. > > > > 3. In FDD, the characteristics of !04B/5B Encoding!1 include: (multiple > answer) > > > A. Sending 4 bits of informations using a 5 bit symbol. > > B. Increasing the clock rate of the transmitter and receiver > to 125Mhz, which establishes an effective data rate of 100Mbps. > > C. Increasing the distance between two FDDI stations to more > than 2km, when using multi-mode fiber. > > D. Providing a workaround for the optical Bypass Relay. > > > > 4. Examine the following: > > > > > > > > > > > > > > > > > > > > > > Based on the information above, which OSPF configurations listed are valid? > (multiple answer) > > > > A. router A > > router OSPF 1 > > network 14.0.0.0 0.255.255.255 area 0 > > router B > > router OSPF 1 > > network 14.0.0.0 0.255.255.255 area 0 > > > > B. router A > > router OSPF 1 > > network 14.1.1.0 0.0.0.255 area 0 > > router B > > router OSPF 2 > > network 14.1.1.0 0.0.0.255 area 0 > > > > C. router A > > router OSPF 1 > > network 14.0.0.0 0.0.255.255 area 0 > > router B > > router OSPF 1 > > network 14.1.0.0 0.0.0.255 area 0 > > > > D. router A > > router OSPF 1 > > network 14.1.1.0 0.0.0.255 area 0 > > router B > > router OSPF 1 > > network 14.1.0.0 0.0.255.255 area 0 > > 5. In reorganization, OSPF areas are realigned. Is this a valid network > design? If not, what changes could be made to the network and/or router > configurations? > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > A. No changes are necessary. > > B. A virtual link could be configured between Area 60 and > area 0. > > C. A serial line or other physical connections could be > installed between devices in Area 60 and Area 0. > > D. Router B could be configured as an Area Border Router > between Area 60 and Area 6. > > E. This is not valid design, and no changes can make it > work. > > > > 6. Which of the following CGMP (Cisco group management protocol) > statements is correct? > > > A. CGMP manages multicast traffic Catalyst 5000 series > switches by allowing directed switching of IP multicast traffic. > > B. CGMP will switch IP multicast packets to all ports in one > specific VLAN. > > C. CGMP filtering requires a network connection from the > Catalyst 5000 series to a router running CGMP. > > D. CGMP handles ARP, SAP, UDP, SSAP and DSAP. > > > > 7. Which statement about RADIUS is true? > > > A. The RADIUS server must you use TCP for its connection the > NAS. > > B. AAA can be configured to direct RADIUS > authentication/authorization to one server and RADIUS accounting to a > different server. > > C. RADIUS supports bi-directional CHAP authentication. > > D. RADIUS is a proprietary protocol that is necessarily > vendor specific. > > E. RADIUS supports command authorization. > > > > 8. Which statements about TACACS+ are true? (multiple answer) > > > A. If more than one TACACS+ server is configured and the > first one does not respond within a given timeout period, the next TACACS+ > server in the list will be contacted. > > B. The TACACS+ server!/s connection to the NAS encrypts the > entire packet. > > C. The TACACS+ server must use TCP for its connection to the > NAS. > > D. The TACACS+ server must use UDP for its connection to the > NAS. > > E. The TACACS+ server may be configured to use TCP or UDP > for its connection to the NAS. > > > > 9. CGMP (Cisco Group Management Protocol) is: > > > A. A serial protocol for communications between routers and > switches. > > B. An alternative protocol that can be used instead of SNMP > to manage a group of routers/switches. > > C. A messaging format for routers to download MAC tables to > allow layer 2 switching in the router. > > D. A protocol that provides dynamic configuration, > forwarding multicast traffic only to ports that have IP multicast clients > attached. > > > > 10. Which of the following statements is NOT accurate regarding Frame > Relay? > > > A. Frame relay is a high-speed, shared bandwidth Network > Layer Protocol. > > B. Frame relay provides error detection. > > C. Frame relay does not provide error recovery. > > D. Frame relay is based on a !0packet-over-circuit!1 > architecture. > > > > 11. A !.default network!/ performs a service in routing. It is used: > > > A. To generate a default route, independent of the routing > protocol implemented in the router. > > B. To select a candidate route computing the gateway of last > resort. > > C. Only when routing is disabled. > > D. To override entries in the routing table that use the > same class of network address. > > > > 12. Examine the following: > > > VERSION 11.2 > > ! > > hostname router > > ! > > boot system flash slot0:rsp-isv-mz.112-B.P > > enable password cisco > > > > If this router has a configuration-register setting of 0x102, select the > proper boot sequence: > > > > A. The router will try to use the image !0rsp-isv-mz, > 112-8P!1 on slot 0, then attempt to boot from a network server, and finally > boot from ROM. > > B. The router will try use the image !0rsp-isv-mz, 112-8P!1 > on slot 0, then attempt to boot from any other valid image in flash, and > finally boot from ROM. > > C. The router will try use the image !0rsp-isv-mz, 112-8P!1 > on slot 0, then it will boot from ROM. > > D. The router will try use the image !0rsp-isv-mz, 112-8P!1 > on slot 0, then it will boot from network server. > > 1.. WAN frame formats generally have which fields in common? > > > A. Flag, address, control, data, FCS > > B. Source address, destination address, length, data, CRC > > C. Flag, source address, destination address, control, data, > FCS > > D. Control, data, CRC > > E. None > > > > 13. The configuration for Router A is as follows: > > > > RouterA#show running-config > > Current configuration: > > Version 11.3 > > > > 1.) hostname RouterA > > 2.) enable-password enablepassword > > 3.) interface Ethernet 0 > > 4.) IP address 191.8.1.1 255.255.255.0 > > 5.) No mop enabled > > 6.) Interface serial 0 > > 7.) IP address 191.8.150.1 255.255.255.0 > > 8.) IP name-Server 255.255.255.255 > > 9.) IP host RouterB 191.8.150.1 191.8.2.1 > > 10.) Snmp-Server community ccie > > 11.) Line vty 0 4 > > 12.) Login > > 13.) Line configure 0\line aux 0 > > 14.) Line vty 0 > > 15.) Password vtypassword > > 16.) Line vty 1 > > 17.) Password vtypassword > > 18.) Line vty 2 > > 19.) Password vtypassword > > 20.) Line vty 3 > > 21.) Password vtypassword > > 22.) Line vty 4 > > 23.) Password vtypassword > > 24.) End > > Router A# > > > > The configuration for Router B is as follows: > > > > RouterB#show running-config > > Current Configuration: > > Version 11.3 > > > > 1.) hostname RouterB > > 2.) enable-password san-fran > > 3.) interface tokenring 0 > > 4.) IP address 191.8.2.1 255.255.255.0 > > 5.) Ring-speed 16 > > 6.) Interface serial 0 > > 7.) IP address 191.8.150.2 255.255.255.0 > > 8.) IP name-Server 255.255.255.255 > > 9.) IP host A 191.8.2.1 191.8.150.1 > > 10.) Snmp-Server community ccie > > 11.) Logging buffered > > 12.) Line vty 0 4 > > 13.) Login > > 14.) Line configure 0 > > 15.) Line aux 0 > > 16.) Line vty 0 > > 17.) Password cisco > > 18.) Line vty 1 > > 19.) Password cisco > > 20.) Line vty 2 > > 21.) Password cisco > > 22.) Line vty 3 > > 23.) Password cisco > > 24.) Line vty 4 > > 25.) End > > RouterB# > > > > Debug is enabled on Router B, but no debug messages appear on the terminal. > Other commands (show commands, etc) seem to be working. What are the > probable causes for this? > > > > A. Router B is not turned on. > > B. Debug information is being sent to A. > > C. The !0terminal monitor!1 command needs to be executed, > if this is a virtual terminal session. > > D. Debug information is being sent to the buffer instead > of to the console terminal. > > E. Debug information is configured at low priority, and > will be displayed at a time when the router is less congested. > > > > 14. What is the only feature NOT included in FastEther Channel? > > > A. Load balancing > > B. Full duplex > > C. Up to 6 interfaces can be bundled into one prot-channel > > D. Support of HSRP > > Fault tolerance _________________________________________________________ Do You Yahoo!? Get your free @yahoo.com address at http://mail.yahoo.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=28889&t=28862 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
