You haven't been following the list Leigh Ann, I sent that URL out a couple weeks ago too!! Unfortunately it comes back with nothing, kinda like the SW/HW comptibility matrix, it list the stuff I'm familiar with but rarely the new and the new is what I need info about!!!!
oh well enough whining, time to dig, (pig) into the Christmas potluck, looks like a nice spread:-) Dave Leigh Anne Chisholm wrote: > > Dave: Don't know if you've seen this, but on a recent "tour" of CCO, I came > across a nifty tool I never knew existed. Cisco has an "Error Message > Decoder" utility on their site that can be accessed by clicking on the > following link: > > http://www.cisco.com/cgi-bin/Support/Errordecoder/home.pl > > (You need to log into Cisco's site in order to use this tool). > > This, and many other handy utilities and tools can be found in the Technical > Assistance Center section of Cisco's website under the "Tool Index" that can > be found at this handy link: > > http://www.cisco.com/kobayashi/support/tac/t_index.shtml > > This index of available tools is something also that I didn't know existed. > Note that the tools available will differ depending on what account type (if > any) you are logged in with... > > -- Leigh Anne > > PS. Not surprisingly since you couldn't find anything on Michael's problem on > Cisco's site, the Error Message Decoder didn't have anything on this message > in its database... > > -----Original Message----- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Michael Williams > Sent: Monday, December 17, 2001 6:00 PM > To: [EMAIL PROTECTED] > Subject: Re: OT: Error on Cat6500..... [7:29411] > > Here's what happened. > > As I mentioned before, I cleared the NVRAM on both Sups separately. But, > when I issued a 'reload' on Sup#1 after clearing, it failed over to Sup#2, > and that's when I started getting this error..... > > So, I powered it down, pulled and reseated both Sups, and turned it back > on. Now the Power light on BOTH sups was red, and lo and behold, when I > cleared NVRAM, I forgot to give it a "boot system sup-bootflash:blahblah", > so it booted the Sup to rommon. > > SO, the moral of the story is, if you get the above error, it's because the > "standy" Sup has booted into rommon. > > =) > > Once I realized that, I consoled into Sup1, gave the boot command, let it > boot, and changed the bootvar to have it boot from the IOS image in > Sup-bootflash. Then I did the same on Sup#2. Problem solved =) > > Mike W. > > -----Original Message----- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > MADMAN > Sent: Monday, December 17, 2001 4:47 PM > To: [EMAIL PROTECTED] > Subject: Re: OT: Error on Cat6500..... [7:29411] > > Funny you mention that. I'm not seeing that particular problem but I > have a couple of customers who have seen some strange messages and I > cannot find any useful docs on %SYS-SP- or %OIR-SP-, the key here is ANY > error messages with -SP-. Hate opening cases cause I can't find simple > info but... > > Dave > > Michael Williams wrote: > > > > I had a Cat6500 setup in the basement and was using for testing on various > > things. We moved it up into our Data Center. I wiped NVRAM on both Sup > > engines (separately), and not it's booted up and running on the Sup in slot > > 2 (with the Sup in slot 1 (supposedly) in standby mode). > > > > >From the console, I get this repeating error message: > > > > %C6KPWR-SP-4-DISABLED: power to module in slot 1 is set off (admin reque) > > > > I never received this message the entire time I was using in the basement. > > I'm going to go and shut it down, yank the two Sups and reseat them just to > > make sure they're okay.... Just curious to see if there was any specific > > cause for this message. I searched Cisco's site to no avail. > > > > Thanks! > > Mike W. > -- > David Madland > Sr. Network Engineer > CCIE# 2016 > Qwest Communications Int. Inc. > [EMAIL PROTECTED] > 612-664-3367 > > "Emotion should reflect reason not guide it" -- David Madland Sr. Network Engineer CCIE# 2016 Qwest Communications Int. Inc. [EMAIL PROTECTED] 612-664-3367 "Emotion should reflect reason not guide it" Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=29504&t=29411 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
