You do NEED to define your SPIDs Dave
John Neiberger wrote: > It appears that the router is dialing but the calls are > failing. Can we see the output of "show isdn stat" as well > as "debug isdn events" and/or "debug isdn q921" and "debug isdn > q931" ? > > John > > ________________________________________________ > Get your own "800" number > Voicemail, fax, email, and a lot more > http://www.ureach.com/reg/tag > > ---- On Mon, 31 Dec 2001, McHugh Randy ([EMAIL PROTECTED]) wrote: > > > This is router 1 > > r1#sh run int bri 0 > > Building configuration... > > > > Current configuration : 124 bytes > > ! > > interface BRI0 > > ip address 172.16.2.1 255.255.255.0 > > dialer string 2002 > > dialer-group 1 > > isdn switch-type basic-5ess > > end > > dialer-list 1 protocol ip permit > > r1#sh dialer > > > > BRI0 - dialer type = ISDN > > > > Dial String Successes Failures Last DNIS Last > status > > 2002 0 10 00:10:08 > failed > > Default > > 0 incoming call(s) have been screened. > > 0 incoming call(s) rejected for callback. > > > > BRI0:1 - dialer type = ISDN > > Idle timer (120 secs), Fast idle timer (20 secs) > > Wait for carrier (30 secs), Re-enable (15 secs) > > Dialer state is idle > > > > BRI0:2 - dialer type = ISDN > > Idle timer (120 secs), Fast idle timer (20 secs) > > Wait for carrier (30 secs), Re-enable (15 secs) > > Dialer state is idle > > r1# > > 01:30:17: BR0 DDR: cdp, 275 bytes, outgoing uninteresting (no > list > > matched) > > 01:30:17: BR0 DDR: sending broadcast to default destination -- > failed, > > not > > connected > > > > This is router 2 > > r2#sh run int bri 0 > > Building configuration... > > > > Current configuration : 124 bytes > > ! > > interface BRI0 > > ip address 172.16.2.2 255.255.255.0 > > dialer string 2001 > > dialer-group 1 > > isdn switch-type basic-5ess > > end > > dialer-list 1 protocol ip permit > > > > r2#sh dialer > > > > BRI0 - dialer type = ISDN > > > > Dial String Successes Failures Last DNIS Last > status > > 2001 0 2 00:16:14 > failed > > Default > > 0 incoming call(s) have been screened. > > 0 incoming call(s) rejected for callback. > > > > BRI0:1 - dialer type = ISDN > > Idle timer (120 secs), Fast idle timer (20 secs) > > Wait for carrier (30 secs), Re-enable (15 secs) > > Dialer state is idle > > > > BRI0:2 - dialer type = ISDN > > Idle timer (120 secs), Fast idle timer (20 secs) > > Wait for carrier (30 secs), Re-enable (15 secs) > > Dialer state is idle > > > > > > I tried reversing the numbers for the dialer string like 2001 > and 2002 > > on > > each router just in case I had the numbers for the dialer > strings > > reversed > > but that did not help. > > Any suggestions appreciated. > > Thanks > > Randy > [EMAIL PROTECTED] -- David Madland CCIE# 2016 Senior Network Engineer Qwest Communications 612-664-3367 Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=30622&t=30589 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
