I have recent come into posession of a Cisco 516-CS Terminal Server. I want to use this device to control a rack of 8-9 routers, switches, etc....
I am using a standard Cisco Console Roll-Over cable to connect a port of the 516-CS to the Console Port the Router. In my setup I'm using port 5 of the 516-CS. The loopback address is 192.168.1.1 I have setup a loopback interface on the 516-CS. I then issue the following command telnet 192.168.1.1 2005, I get an immediate respone that the connection is open and nothing else happpens, I then hit enter a couple of times on the 516-CS which eventually hangs the device and it has to be rebooted. Here are the config's for the 516-CS and one router. Any help, ideas and suggestions are greatly welcome. sh config Using 394 out of 32512 bytes ! version 9.21 no service pad ! hostname CS ! enable password cisco ! ! interface Loopback1 ip address 192.168.1.1 255.255.255.0 ! interface Ethernet0 ip address 172.13.2.251 255.255.255.0 ! ! line con 0 line 1 8 no exec session-timeout 30 transport input telnet stopbits 1 line 9 16 no exec exec-timeout 0 0 session-timeout 30 transport input telnet line vty 0 4 password cisco login ! end urrent configuration : 1876 bytes ! version 12.1 service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname cisco2621 ! enable secret 5 $1$.hWv$a/EZI7ljy6CyqTvL/kobp/ ! username 2611 password 0 cisco username 2621 password 0 cisco username itc2611 password 0 cisco ! ! ! ! ip subnet-zero no ip finger ! isdn switch-type basic-ni ! ! ! interface FastEthernet0/0 ip address 172.13.2.252 255.255.255.0 duplex auto speed auto ! interface BRI0/0 no ip address encapsulation ppp dialer pool-member 1 isdn switch-type basic-ni isdn spid1 0835866101 8358661 isdn spid2 0835866301 8358663 ppp authentication chap ! interface Serial0/0 no ip address encapsulation frame-relay ! interface Serial0/0.1 point-to-point ip address 1.1.1.1 255.255.255.252 frame-relay interface-dlci 100 ! interface Serial0/0.2 point-to-point ip address 1.1.1.5 255.255.255.252 frame-relay interface-dlci 101 ! interface Serial0/0.3 point-to-point ip address 1.1.1.9 255.255.255.252 frame-relay interface-dlci 102 ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Dialer1 ip address 10.1.1.1 255.255.255.252 encapsulation ppp dialer pool 1 dialer idle-timeout 10000 dialer string 8358662 dialer load-threshold 3 either dialer-group 1 ppp chap hostname 2621 ppp chap password 7 030752180500 ppp multilink ! router eigrp 100 redistribute static network 1.0.0.0 network 10.0.0.0 network 100.0.0.0 auto-summary no eigrp log-neighbor-changes ! ip classless ip route 0.0.0.0 0.0.0.0 10.1.1.2 120 no ip http server ! access-list 100 deny eigrp any any access-list 100 permit ip any any dialer-list 1 protocol ip list 100 banner exec ^CHello Welcome to the Lab^C banner motd ^CHello Welcome to the Cisco 2621 Router^C ! line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 password cisco login ! end Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=35227&t=35227 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
