You only have two images to worry about. One on the supervisor's which they share. (Upgrade one, give it a few minutes and it will upgrade the other one automatically) And one on the RSM.
Same for config files: One which the supervisors share and one for the RSM. Good Luck Gaz ""Sim, CT (Chee Tong)"" wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > Hi.. Sorry some more questions. > 1)I found although there are 5 module in my switch, when I do "sh flash", > only one binary flash file appear. Which module does the belong to? > > 2)How to see the flash code file for other module. I found I can only go to > the RSM by typing "session 4" and find out the flash ver. But I can't go to > other modules like standby supervisor and 10/100BaseTX Ethernet. > > 3)I found that there is a entry in my switch config, set boot system flash > bootflash:cat5000-sup3.5-1-1.bin. It should be refer to my main supervisor > module and I know where the RSM config. But is there any configuration file > for standby supervisor module and 10/100100BaseTX Ethernet module? If yes, > how to see them, Do we have to set the boot system flash in their config? > > 4)I found the URL > http://www.cisco.com/univercd/cc/td/doc/product/lan/cat5000/c5krn/sw_rns/78_ > 6583.htm#xtocid3 is to show the various flash code's release note. Do you > know the flash upgrade guide for cat5505. > > $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ > Cat55-L8-1> (enable) sh module > Mod Slot Ports Module-Type Model Status > --- ---- ----- ------------------------- ------------------- -------- > 1 1 2 1000BaseSX Supervisor WS-X5534 ok > 2 2 2 1000BaseSX Supervisor WS-X5534 standby > 3 3 24 10/100BaseTX Ethernet WS-X5225R ok > 4 4 1 Route Switch WS-X5302 ok > 5 5 24 10/100BaseTX Ethernet WS-X5225R ok > > > Cat55-L8-1> (enable) sh flash > -#- ED --type-- --crc--- -seek-- nlen -length- -----date/time------ name > 1 .D ffffffff a638976e 3627ec 23 3286891 Mar 10 2000 18:17:19 > cat5000-sup3.4-3-1a.bi > n > 2 .. ffffffff ce0e4293 70f7e8 22 3854201 Apr 25 2000 04:47:50 > cat5000-sup3.5-1-1.bin > > > #set boot command > set boot config-register 0x102 > set boot system flash bootflash:cat5000-sup3.5-1-1.bin > > > > > > -----Original Message----- > From: Robertson, Douglas [mailto:[EMAIL PROTECTED]] > Sent: Wednesday, March 06, 2002 9:00 PM > To: Sim, CT (Chee Tong); [EMAIL PROTECTED] > Subject: RE: software upgrade for Cat5505 switch for each module? [7: 37382 > ] > > Review the following document on CCO, > http://www.cisco.com/univercd/cc/td/doc/product/lan/cat5000/c5krn/sw_rns/78_ > 6583.htm#xtocid3 the document indicates the upgrade path for Catalyst 5000 > switches, it also has a table that shows which versions of CAT OS is > supported by each module. Depending on what you needs are you may have to > upgrade all the modules, the RSM runs IOS and will have different criteria > to consider when upgrading. To upgrade the module you can use the following > command : download . The download first > checks to see if the downloaded image is correct for the particular module > it then installs the image. As far as which image you would require depends > on the type of hardware you are downloading to, for the supervisor cards you > need to determine if they are supII, supIII, or supII gigabit. > > Hope this helps > > Doug > > -----Original Message----- > From: Daniel Cotts [mailto:[EMAIL PROTECTED]] > Sent: Thursday, March 07, 2002 12:13 AM > To: 'Sim, CT (Chee Tong)'; [EMAIL PROTECTED] > Subject: RE: software upgrade for Cat5505 switch for each module? [7: 37383 > ] > > Sup III cards require sup3 code. The versions that just say sup are for Sup > I & II cards. Sup III cards have slots for Flash Cards. If you have those, > then you can store multiple images. You must have a line in your config > something like "boot system flash: image name" If your switch goes looking > for a file that no longer exists it becomes unhappy. > Version 6 of Cat code requires 64 MB of DRAM. There may also be a Firmware > requirement. Check the docs for the desired image. Some of the first > paragraphs will explain the requirements. > The RSM is a router on a blade. It has its own IOS image that you would load > seperately. > > > > > -----Original Message----- > From: Sim, CT (Chee Tong) [mailto:[EMAIL PROTECTED]] > Sent: Wednesday, March 06, 2002 4:03 AM > To: [EMAIL PROTECTED] > Subject: software upgrade for Cat5505 switch for each module? [7:37382] > > > Hi.. I want to upgrade my catalyst 5505 switch (set based switch). I have > never done it for set based cat5505 before and I found that there are a lot > of modules in my switch, eg two supervisor module and two 10/100TX Ethernet, > one RSM. Do I have upgrade the IOS for every modules? > > > > I found that when I type show flash, I got only binary file > cat5000-sup3.5-1-1.bin. Can I just download the binary file from web eg > > cat5000-sup3.5-5-7a.bin and then upgrade by typing copy tftp flash. Will > > cat5000-sup3.5-5-7a.bin overwrite the old cat5000-sup3.5-1-1.bin or there > will be two copy of binary file in the flash. > > > > I saw there are a few type of flash code eg Catalyst 5000 Supervisor G Flash > Code, Catalyst 5000 Supervisor 3 Flash Code, and Catalyst 5000 Supervisor > Flash Code. Can I use any one of them. > > > > Thanks > > > > > > ================================================================== > De informatie opgenomen in dit bericht kan vertrouwelijk zijn en > is uitsluitend bestemd voor de geadresseerde. Indien u dit bericht > onterecht ontvangt wordt u verzocht de inhoud niet te gebruiken en > de afzender direct te informeren door het bericht te retourneren. > ================================================================== > The information contained in this message may be confidential > and is intended to be exclusively for the addressee. Should you > receive this message unintentionally, please do not use the contents > herein and notify the sender immediately by return e-mail. > > > ================================================================== Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=37648&t=37648 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
