Most people would say it's your config-reg, but that's not the problem. Even though your config-reg is set to 0x2102, it's booting off the booroms (the (boot) in your prompt below). Your flash either has a corrupt image on it, a non-applicable image, or they are blank. Either case, your booting from your bootroms. So...
More than likely it's one of the followng: 1) Bad flash 2) Bad DRAM If you have some known good flash, put that in there and give it a whack. thanks, -Brad Ellis CCIE#5796 (R&S / Security) [EMAIL PROTECTED] Cisco home labs: www.optsys.net ""G Chung"" wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > Hi! > > I recently bought some flash (16mb)for my cisco 2514. > Everytime I try to copy a file to flash, it keep > giving me the following error message. > > Accessing file 'c2500-js-l.122-7b.bin' on > 10.100.100.30... > Loading c2500-js-l.122-7b.bin from 10.100.100.30 (via > Ethernet0): ! [OK] > > Device needs erasure before copying new file > Erase flash device before writing? [confirm]y > > Copy 'c2500-js-l.122-7b.bin' from server > as 'c2500-js-l.122-7b.bin' into Flash WITH erase? > [yes/no]y > Erasing device... > eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee > ee ...erased > Loading c2500-js-l.122-7b.bin from 10.100.100.30 (via > Ethernet0): ! > % Flash is set to read-only in hardware > System flash: at location 0x3000240 - wrote > 0x48E7FFFC, read 0xFFFFFFFF > COPY: Image checksum verification failure > > % Flash is set to read-only in hardware > System flash: at location 0x3000040 - wrote 0xE7FFFC > , read 0xFFFFFFFF > TFTP from 10.100.100.30 failed/aborted > > Verifying checksum... invalid (expected 0x3AE1, > computed 0x0) > % Flash is set to read-only in hardware > System flash: at location 0x3000000 - wrote > 0xBAD00B1E, read 0xFFFFFFFF > Flash copy took 0:00:09 [hh:mm:ss] > C2514(boot)# > > > ***HERE is the the sh ver. It indicated that flash is > readable and writeable. Do I have bad Flash?*** > > Copyright (c) 1986-1995 by cisco Systems, Inc. > Compiled Thu 23-Mar-95 02:08 by kmac > Image text-base: 0x01020000, data-base: 0x00001000 > ROM: System Bootstrap, Version 5.2(5), RELEASE > SOFTWARE > C2514 uptime is 10 minutes > System restarted by power-on > Running default software > cisco 2500 (68030) processor (revision D) with > 16380K/2048K bytes of memory. > Processor board serial number 02007228 > X.25 software, Version 2.0, NET2, BFE and GOSIP > compliant. > Authorized for Enterprise software set. (0x0) > 2 Ethernet/IEEE 802.3 interfaces. > 2 Serial network interfaces. > 32K bytes of non-volatile configuration memory. > 16384K bytes of processor board System flash > (Read/Write) > Configuration register is 0x2102 > C2514(boot)# > > Thank you any help you can give > > George > > __________________________________________________ > Do You Yahoo!? > Yahoo! - Official partner of 2002 FIFA World Cup > http://fifaworldcup.yahoo.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=47762&t=47760 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
