Try using VPI 1 instead of 0. I know 0 is a valid option but I have seen it not work and we don't use it for other reasons that I don't know the history of. Also the framing and scrambling parameters are needed if I recall.
Here is a config I know works cause I was using it in the lab: interface ATM0/0/0 no ip address no ip directed-broadcast no ip route-cache cef no atm ilmi-keepalive scrambling cell-payload framing cbitplcp ! interface ATM0/0/1 no ip address no ip directed-broadcast no ip route-cache cef no atm ilmi-keepalive atm pvc 1 32 interface ATM0/0/0 1 32 scrambling cell-payload framing cbitplcp Dave The Edward Groove wrote: > > Hey Andre, > > Thanks for your help thus far...Yes, all the > interfaces say up/up. I have changed the router > versions to 3.1 as you suggested. I still have no ip > connectivity. Any other suggestions? > > The routers/l1010 both have very up-to-date software, > as shown below from my "sho ver". > > Thanks, > > Eddie > > ROUTER 1: > > 3600 Software (C3620-IS-M), Version 12.2(2)XT3, EARLY > DEPLOYMENT RELEASE SOFTWARE (fc1) > TAC Support: http://www.cisco.com/tac > Compiled Wed 13-Mar-02 23:15 by shawnk > Image text-base: 0x600089A8, data-base: 0x6153A000 > > ROM: System Bootstrap, Version 11.1(20)AA2, EARLY > DEPLOYMENT RELEASE SOFTWARE (fc1) > > R3620-1 uptime is 1 day, 13 hours, 50 minutes > System returned to ROM by power-on > System image file is "flash:c3620-is-mz.122-2.xt3.bin" > > cisco 3620 (R4700) processor (revision 0x81) with > 58368K/7168K bytes of memory. > Processor board ID 20530878 > R4700 CPU at 80Mhz, Implementation 33, Rev 1.0 > Bridging software. > X.25 software, Version 3.0.0. > 1 FastEthernet/IEEE 802.3 interface(s) > 1 Serial network interface(s) > 1 ATM network interface(s) > DRAM configuration is 32 bits wide with parity > disabled. > 29K bytes of non-volatile configuration memory. > 16384K bytes of processor board System flash > (Read/Write) > 8192K bytes of processor board PCMCIA Slot0 flash > (Read/Write) > > Configuration register is 0x2182 > > ---------------------------------------------------- > > ROUTER 2: > > 3600 Software (C3620-IS-M), Version 12.2(2)XT3, EARLY > DEPLOYMENT RELEASE SOFTWARE (fc1) > TAC Support: http://www.cisco.com/tac > Compiled Wed 13-Mar-02 23:15 by shawnk > Image text-base: 0x600089A8, data-base: 0x6153A000 > > ROM: System Bootstrap, Version 11.1(20)AA2, EARLY > DEPLOYMENT RELEASE SOFTWARE (fc1) > > r3620-2 uptime is 1 day, 13 hours, 51 minutes > System returned to ROM by power-on > System image file is "flash:c3620-is-mz.122-2.xt3.bin" > > cisco 3620 (R4700) processor (revision 0x81) with > 58368K/7168K bytes of memory. > Processor board ID 21963872 > R4700 CPU at 80Mhz, Implementation 33, Rev 1.0 > Bridging software. > X.25 software, Version 3.0.0. > 1 FastEthernet/IEEE 802.3 interface(s) > 1 Serial network interface(s) > 1 ATM network interface(s) > DRAM configuration is 32 bits wide with parity > disabled. > 29K bytes of non-volatile configuration memory. > 32768K bytes of processor board System flash > (Read/Write) > > Configuration register is 0x2182 > > ------------------------------------------------------- > > L1010: > > Cisco Internetwork Operating System Software > IOS (tm) LS1010 WA3-4 Software (LS1010-WP-M), Version > 11.2(10)WA3(4a), RELEASE SOFTWARE > Copyright (c) 1986-1902 by cisco Systems, Inc. > Compiled Thu 14-Mar-02 14:50 by integ > Image text-base: 0x600108D0, data-base: 0x60436000 > > ROM: System Bootstrap, Version 11.2(1.4.WA3.0) [integ > 1.4.WA3.0], RELEASE SOFTWARE > > L1010 uptime is 1 day, 13 hours, 24 minutes > System restarted by reload > System image file is > "bootflash:ls1010-wp-mz.112-10.wa3.4a.bin", booted via > bootflash > > cisco ASP (R4600) processor with 32768K bytes of > memory. > R4700 processor, Implementation 33, Revision 1.0 > Last reset from power-on > 1 Ethernet/IEEE 802.3 interface(s) > 4 ATM network interface(s) > 123K bytes of non-volatile configuration memory. > > 8192K bytes of Flash internal SIMM (Sector size 256K). > Configuration register is 0x2101 > > --- Andre Riscalla > wrote: > > > > A couple of suggestions: > > > > 1) Verify that your ATM interfaces are up and up > > which i assume you > > already did. > > > > 2) Since your LS1010 ATM interfaces are setup with > > UNI version 3.1, change > > your ATM uni version on your routers to be 3.1. (The > > default is 3.0). > > > > Please provide the IOS version you are running on > > the LS1010 and on the > > routers as well. > > > > Thanks. > > > > AR- > > > > > > On Mon, 22 Jul 2002, Edward Sohn wrote: > > > > > Thanks for the reply, Andre... > > > > > > Hmmm...I was thinking the same way you did at > > first, but then the book's > > > configuration actually has both "atm pvc" commands > > in each interface. > > > Is that a typo, then? > > > > > > Even so, I cannot get connectivity between my > > routers. Here is my "sho > > > run" for the L1010 and 2 routers: > > > > > > L1010: > > > > > > Current configuration: > > > ! > > > version 11.2 > > > no service pad > > > no service password-encryption > > > no service udp-small-servers > > > no service tcp-small-servers > > > ! > > > hostname L1010 > > > ! > > > ! > > > ip host-routing > > > no ip domain-lookup > > > ! > > > atm address > > 47.0091.8100.0000.0050.a2c6.4001.0050.a2c6.4001.00 > > > atm router pnni > > > node 1 level 56 lowest > > > redistribute atm-static > > > ! > > > ! > > > interface ATM12/0/0 > > > no atm auto-configuration > > > atm uni version 3.1 > > > atm maxvp-number 8 > > > atm maxvc-number 8192 > > > atm maxvpi-bits 3 > > > atm maxvci-bits 10 > > > ! > > > interface ATM12/0/1 > > > ! > > > interface ATM12/0/2 > > > no atm auto-configuration > > > atm uni version 3.1 > > > atm maxvp-number 8 > > > atm maxvc-number 8192 > > > atm maxvpi-bits 3 > > > atm maxvci-bits 10 > > > atm pvc 0 121 interface ATM12/0/0 0 112 > > > ! > > > interface ATM12/0/3 > > > ! > > > interface ATM13/0/0 > > > ip address 175.128.100.5 255.255.255.0 > > > atm maxvp-number 0 > > > ! > > > interface Ethernet13/0/0 > > > no ip address > > > ! > > > no ip classless > > > ! > > > line con 0 > > > exec-timeout 0 0 > > > line aux 0 > > > line vty 0 4 > > > login > > > ! > > > end > > > > > > ROUTER 1 > > > > > > Current configuration : 854 bytes > > > ! > > > version 12.2 > > > service timestamps debug uptime > > > service timestamps log uptime > > > no service password-encryption > > > ! > > > hostname R3620-1 > > > ! > > > ! > > > ip subnet-zero > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > fax interface-type fax-mail > > > mta receive maximum-recipients 0 > > > ! > > > ! > > > ! > > > ! > > > interface FastEthernet0/0 > > > ip address 165.128.1.1 255.255.255.0 > > > duplex auto > > > speed auto > > > ! > > > interface Serial0/0 > > > no ip address > > > shutdown > > > clockrate 2000000 > > > ! > > > interface ATM1/0 > > > no ip address > > > no atm ilmi-keepalive > > > ! > > > interface ATM1/0.1 multipoint > > > ip address 165.128.100.1 255.255.255.0 > > > map-group ip-Pvc > > > atm pvc 112 0 112 aal5snap > > > ! > > > router eigrp 100 > > > network 165.128.0.0 > > > auto-summary > > > no eigrp log-neighbor-changes > > > ! > > > ip classless > > > ip http server > > > ! > > > ! > > > ! > > > map-list ip-Pvc > > > ip 165.128.100.2 atm-vc 112 broadcast > > > ! > > > call rsvp-sync > > > ! > > > ! > > > mgcp profile default > > > ! > > > dial-peer cor custom > > > ! > > > ! > > > ! > > > ! > > > line con 0 > > > line aux 0 > > > line vty 0 4 > > > ! > > > ! > > > end > > > > > > ROUTER 2: > > > > > > Current configuration : 835 bytes > > > ! > > > version 12.2 > > > service timestamps debug uptime > > > service timestamps log uptime > > > no service password-encryption > > > ! > > > hostname r3620-2 > > > ! > > > ! > > > ip subnet-zero > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > fax interface-type fax-mail > > > mta receive maximum-recipients 0 > > > ! > > > ! > > > ! > > > ! > > > === message truncated === > > __________________________________________________ > Do You Yahoo!? > Yahoo! Health - Feel better, live better > http://health.yahoo.com -- David Madland Sr. Network Engineer CCIE# 2016 Qwest Communications Int. Inc. [EMAIL PROTECTED] 612-664-3367 "Emotion should reflect reason not guide it" Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=49435&t=49352 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
