Thanks. I only have to make the correct access-list for all the IP address that I manage in the Giga interface and after to apply the command rate-limit.It is important to know because in case of congestion problem in the WAN links this could be a solution.
Thanks for your help. >From: "Chuck's Long Road" >Reply-To: "Chuck's Long Road" >To: [EMAIL PROTECTED] >Subject: Re: BW Limit. [7:51407] >Date: Wed, 14 Aug 2002 23:59:54 GMT > >for that matter, your English is better than mine. I can't tell the >difference between "you" and "I" below. > >I meant to say your English is far better than any second language "I" >speak. > >sorry - did not mean to denigrate. > >Chuck > >-- >coming soon: > >www.chuckslongroad.info >""Chuck's Long Road"" wrote in message >[EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > > no problemo. your English is far better than any language you speak > > natively, I guarantee it! > > > > in any case, I've sanitized this one, but it is a working config at a >live > > customer site: > > > > there is some good QoS documentation to be found on CCO, particualrly in >the > > 3550 switch Configuration Guide, which will explain what all the numbers > > mean. Cisco can be a bit unclear, because some of the numbers are Bytes, >and > > others are bits. > > > > HTH > > > > > > interface FastEthernet0/1 > > description Connected to WAN > > ip address x.y.z.1 255.255.255.0 > > no ip directed-broadcast > > rate-limit input access-group 101 1544000 289500 579000 conform-action > > transmit exceed-action drop > > rate-limit input access-group 102 384000 72000 144000 conform-action > > transmit exceed-action drop > > rate-limit input access-group 103 384000 72000 144000 conform-action > > transmit exceed-action drop > > rate-limit input access-group 104 384000 72000 144000 conform-action > > transmit exceed-action drop > > rate-limit output access-group 101 1544000 289500 579000 conform-action > > transmit exceed-action drop > > rate-limit output access-group 102 384000 72000 144000 conform-action > > transmitexceed-action drop > > rate-limit output access-group 103 128000 24000 24000 conform-action > > transmit exceed-action drop > > rate-limit output access-group 104 384000 72000 144000 conform-action > > transmitexceed-action drop > > speed 100 > > full-duplex > > no cdp enable > > ! > > interface Serial0/1 > > description Connected to Verio > > ip address a.b.c.d w.x.y.z > > no ip directed-broadcast > > ip load-sharing per-packet > > no fair-queue > > service-module t1 timeslots 1-24 > > no cdp enable > > ! > > ip classless > > ip route 0.0.0.0 0.0.0.0 Serial0/0 > > ip route 0.0.0.0 0.0.0.0 Serial0/1 > > no ip http server > > ! > > access-list 101 permit ip host x.y.z.100 any > > access-list 101 permit ip host x.y.z.150 any > > access-list 101 permit ip host x.y.z.151 any > > access-list 101 permit ip host x.y.z.152 any > > access-list 101 permit ip host x.y.z.153 any > > access-list 101 permit ip host x.y.z.154 any > > access-list 101 permit ip host x.y.z.101 any > > access-list 101 permit ip host x.y.z.102 any > > access-list 101 permit ip host x.y.z.103 any > > access-list 101 permit ip host x.y.z.104 any > > access-list 101 permit ip any host x.y.z.100 > > access-list 101 permit ip any host x.y.z.101 > > access-list 101 permit ip any host x.y.z.102 > > access-list 101 permit ip any host x.y.z.103 > > access-list 101 permit ip any host x.y.z.104 > > access-list 101 permit ip any host x.y.z.150 > > access-list 101 permit ip any host x.y.z.151 > > access-list 101 permit ip any host x.y.z.152 > > access-list 101 permit ip any host x.y.z.153 > > access-list 101 permit ip any host x.y.z.154 > > access-list 102 permit ip host x.y.z.113 any > > access-list 102 permit ip any host x.y.z.113 > > access-list 103 permit ip host x.y.z.111 any > > access-list 103 permit ip any host x.y.z.111 > > access-list 104 permit ip host x.y.z.105 any > > access-list 104 permit ip host x.y.z.106 any > > access-list 104 permit ip host x.y.z.107 any > > access-list 104 permit ip host x.y.z.108 any > > access-list 104 permit ip host x.y.z.109 any > > access-list 104 permit ip any host x.y.z.105 > > access-list 104 permit ip any host x.y.z.106 > > access-list 104 permit ip any host x.y.z.107 > > access-list 104 permit ip any host x.y.z.108 > > access-list 104 permit ip any host x.y.z.109 > > > > > > -- > > coming soon: > > > > www.chuckslongroad.info > > ""Jose Tomas Pinal Salvador"" wrote in message > > [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > > > Hello Group. > > > > > > Currently, I have a router Cisco 7513 with 7 WAN interfaces, 2 Fast > > ethernet > > > and 2 Giga ethernet. I can limit the BW genered by the 2 Fast Ethernet > > with > > > a Packetshaper machine but I am not allow to control the traffic in >the >2 > > > Giga Ethernet interface with the Packetshaper(the equipment doesn4t > > support > > > this interface type) so I would like to make this work in the router >with > > > any command like traffic shaping or rate limit. Could anybody help me? > > > > > > Note:I need to control all the total traffic across the giga >interface. > > > Sorry for my bad english. It is not my native language. > > > > > > > > > > > > > > > _________________________________________________________________ > > > Chat with friends online, try MSN Messenger: http://messenger.msn.com _________________________________________________________________ Send and receive Hotmail on your mobile device: http://mobile.msn.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=51457&t=51407 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
