Do you have basic layer one working? show atm int atm 5/1/0 should be a start. Try the various show atm commands. My atm experience uses the 11.x command set which is quite different from what you have. You might want to try that older command set once basic connectivity between boxes is confirmed. There should be some configs on the docs for the CX-AIP card.
> -----Original Message----- > From: Tangled Up in Blue [mailto:[EMAIL PROTECTED]] > Sent: Thursday, October 10, 2002 10:11 AM > To: [EMAIL PROTECTED] > Subject: LS1010 problem [7:55275] > > > I can't get a 3600 and a 7500 w/ ATM DS3 ints to communicate > over the PVC > through the LS1010! > > All documented configuration I've found is v. simple and > straightforward, > but something is amiss. Any pointers, advice from the > groupstudy guys would > be great (Note, I have a TAC case open on this and they > haven't been able to > solve it yet): > > Here's a diagram of what we have set up. Very simple setup we have: > > maingw7500 - LS1010 - 3600 > atm5/1/0.40 --- atm0/0/0 | atm0/0/1 > --------atm1/0 > pvc3/40 ------------ pvc 3/40 pvc3/50 > ----------pvc3/50 > > > Now for the interface configs on the routers and the entire > config of the > LS1010: > > VGW7500 (IOS Version 12.0(9)S) > > interface ATM5/1/0 > no ip address > no ip directed-broadcast > ip route-cache flow > no ip route-cache cef > no ip route-cache distributed > atm uni-version 3.1 > no atm auto-configuration > atm ilmi-keepalive > no atm address-registration > atm ilmi-pvc-discovery > ! > interface ATM5/1/0.40 point-to-point > ip address 150.240.45.1 255.255.255.252 > no ip directed-broadcast > pvc 3/40 > protocol ip 150.240.45.2 > no ilmi manage > oam-pvc 0 ****NOTE**** here oam-pvc manage brings down the > interface! > encapsulation aal5snap > > ----------------------------------------------- > > Loaner3600 (IOS Version 12.1(5)T5) > > interface ATM1/0 > no ip address > ip route-cache flow > atm uni-version 3.1 > no atm auto-configuration > atm ilmi-keepalive > no atm address-registration > atm ilmi-pvc-discovery > ! > interface ATM1/0.50 point-to-point > ip address 150.240.45.2 255.255.255.252 > pvc 3/50 > protocol ip 150.240.45.1 > oam-pvc manage > encapsulation aal5snap > > > ------------------------------------------------- > > SW1010_Lightstream(IOS Version 12.1(7a)EY3) > > Current configuration : 1589 bytes > ! > version 12.1 > no service pad > service timestamps debug uptime > service timestamps log uptime > service password-encryption > ! > hostname sw1010 > ! > enable secret 5 xxx > ! > network-clock-select 1 System clock > sdm ipqos zero > sdm policy 0 > ip subnet-zero > no ip finger > ! > ! > atm address 47.0091.8100.0000.0009.b71c.3e01.0009.b71c.3e01.00 > atm router pnni > no aesa embedded-number left-justified > node 1 level 56 lowest > redistribute atm-static > ! > ! > ! > ! > interface ATM0/0/0 > no ip address > no atm auto-configuration > no atm address-registration > ! > interface ATM0/0/1 > no ip address > no atm auto-configuration > no atm address-registration > atm pvc 3 50 interface ATM0/0/0 3 40 > ! > interface ATM0/0/2 > no ip address > no ip route-cache cef > shutdown > no atm auto-configuration > no atm address-registration > atm uni version 3.1 > ! > interface ATM0/0/3 > no ip address > shutdown > ! > interface ATM0 > no ip address > atm oam interface ATM0/0/0 0 16 seg-loopback rdi > atm oam interface ATM0/0/1 0 16 seg-loopback rdi > atm oam interface ATM0/0/2 0 16 seg-loopback rdi > atm oam interface ATM0/0/3 0 16 seg-loopback rdi > atm oam interface ATM0/0/0 0 5 seg-loopback rdi > atm oam interface ATM0/0/1 0 5 seg-loopback rdi > atm oam interface ATM0/0/2 0 5 seg-loopback rdi > atm oam interface ATM0/0/3 0 5 seg-loopback rdi > ! > interface Ethernet0 > ip address 150.240.150.154 255.255.255.0 > ! > ip classless > ip route 0.0.0.0 0.0.0.0 Ethernet0 > no ip http server > ! > ! > ! > line con 0 > transport input none > line aux 0 > line vty 0 4 > exec-timeout 120 0 > password 7 xxx > login > ! > end > > -------------------------------- > > NOTES: > > - When the routers are terminated with a physical loopback > they ping their > own ATM ints just fine. > - All interfaces on the routers have been in production in > recent past. > - SW1010 can terminate its interfaces w/ physical loopback > and it looks fine > - 3600 interface stopped flapping when we extended its cable. > - Routers can ping their own ATM ints also when they are > plugged into LS1010 > AND the other LS1010 interface it is mapped to is plugged > into itself with > at physical loopback. > - 3600 can ping its own ATM int even when it is plugged into > LS1010 AND 7500 > is plugged into other LS1010 interface to which its mapped > - Also, on the LS1010, when we do a "ping atm interface atm0/0/1 3 50 > end-loopback" command it works fine (this is with a normal > setup like i just > mentioned above), but the same "ping atm" command mapping to > the 7500's > interface and pvc does not work because we can't run OAM-PVC > MANAGE on the > 7500 sub-int without it bringing down the interface?? > - Throughout this process we have occasionally been able to get pings > through from the 3600 atm int to the 7500 atm int. > - We've tried many debugs, and one common debug message on pings is > "encapsulation failed", but we have aal5snap defined on both > ends of the PVC > - I know we don't need ILMI on a PVC, but it helps for debugging > - Both atm interfaces on the routers are set to CLOCKING=LINE, and the > LS1010 is set to "Current clock source:System clock, priority:1" > > Any advice or help would be appreciated! > > Jason Evans Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=55285&t=55275 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
