Hello everybody ! I am trying to set up a pci wireless card up on a fedora 6 (kde) box. Now I installed the card with ndiswrapper using the drivers on the cd. I have got this card working all ok in unbutu 64 bit using wird as my access. Now with knetworkmanager it just stops at configing device 28% and refuses to connect. Thanks in advance for any help.
Excuse the size of post ! Linux Angelmedia 2.6.22.7-57.fc6 #1 SMP Fri Sep 21 20:23:24 EDT 2007 i686 athlon i386 GNU/Linux [02:08.0 Ethernet controller: Marvell Technology Group Ltd. 88w8335 [Libertas] 802.11b/g Wireless (rev 03) Subsystem: Marvell Technology Group Ltd. 88w8335 [Libertas] 802.11b/g Wireless Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 21 Memory at fdce0000 (32-bit, non-prefetchable) [size=64K] Memory at fdcd0000 (32-bit, non-prefetchable) [size=64K] Capabilities: [40] Power Management version 2 [EMAIL PROTECTED] mythtv]# iwconfig lo no wireless extensions. Warning: Driver for device wlan0 has been compiled with version 22 of Wireless Extension, while this program supports up to version 20. Some things may be broken... wlan0 IEEE 802.11g ESSID:off/any Nickname:"Angelmedia" Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated Bit Rate=48 Mb/s Sensitivity=-200 dBm RTS thr=2346 B Fragment thr=2346 B Encryption key:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 ndiswrapper -l netmw125 : driver installed device (11AB:1FAA) present [EMAIL PROTECTED] mythtv]# wpa_supplicant -i wlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf -D ndiswrapper -d Initializing interface 'wlan0' conf '/etc/wpa_supplicant/wpa_supplicant.conf' driver 'ndiswrapper' ctrl_interface 'N/A' Configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' -> '/etc/wpa_supplicant/wpa_supplicant.conf' Reading configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' ctrl_interface='/var/run/wpa_supplicant' ctrl_interface_group=10 (from group name 'wheel') Priority group 0 id=0 ssid='peos' Initializing interface (2) 'wlan0' EAPOL: SUPP_PAE entering state DISCONNECTED EAPOL: KEY_RX entering state NO_KEY_RECEIVE EAPOL: SUPP_BE entering state INITIALIZE EAP: EAP entering state DISABLED EAPOL: External notification - portEnabled=0 EAPOL: External notification - portValid=0 SIOCGIWRANGE: WE(compiled)=22 WE(source)=18 enc_capa=0xf capabilities: key_mgmt 0xf enc 0xf Own MAC address: 08:10:74:11:6d:b0 Driver does not support WPA. wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0 Setting scan request: 0 sec 100000 usec Added interface wlan0 Wireless event: cmd=0x8b06 len=8 State: DISCONNECTED -> SCANNING Starting AP scan (broadcast SSID) Scan timeout - try to get results ioctl[SIOCGIWSCAN]: Resource temporarily unavailable Scan results: -1 Failed to get scan results Failed to get scan results - try scanning again Setting scan request: 1 sec 0 usec Starting AP scan (broadcast SSID) Scan timeout - try to get results Received 1434 bytes of scan results (6 BSSes) Scan results: 6 Selecting BSS from priority group 0 0: 00:19:5b:4a:f2:e3 ssid='peos' wpa_ie_len=24 rsn_ie_len=0 caps=0x11 selected based on WPA IE Trying to associate with 00:19:5b:4a:f2:e3 (SSID='peos' freq=2412 MHz) Cancelling scan request WPA: clearing own WPA/RSN IE Automatic auth_alg selection: 0x1 WPA: using IEEE 802.11i/D3.0 WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2 WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02 WPA: clearing AP RSN IE WPA: using GTK TKIP WPA: using PTK TKIP WPA: using KEY_MGMT WPA-PSK WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02 No keys have been configured - skip key clearing State: SCANNING -> ASSOCIATING Association request to the driver failed Setting authentication timeout: 15 sec 0 usec EAPOL: External notification - EAP success=0 EAPOL: External notification - EAP fail=0 EAPOL: External notification - portControl=Auto Authentication with 00:00:00:00:00:00 timed out. Added BSSID 00:00:00:00:00:00 into blacklist State: ASSOCIATING -> DISCONNECTED No keys have been configured - skip key clearing EAPOL: External notification - portEnabled=0 EAPOL: External notification - portValid=0 Setting scan request: 0 sec 0 usec Seems that ndiswrapper does not work well with fedora core ? Thanks _______________________________________________ clug-talk mailing list [email protected] http://clug.ca/mailman/listinfo/clug-talk_clug.ca Mailing List Guidelines (http://clug.ca/ml_guidelines.php) **Please remove these lines when replying
