Joel,
I love self tailers! Of the ten winches I have on board, eight are self tailing. They are especially helpful when sailing short handed. As the helmsman, I like to tweak the genoa trim from time to time. My aft winches are great for that. Jake Jake Brodersen “Midnight Mistress” C&C 35 Mk-III Hampton VA From: CnC-List [mailto:[email protected]] On Behalf Of Joel Aronson via CnC-List Sent: Saturday, February 21, 2015 9:56 AM To: Bradley Lumgair; [email protected] Subject: Re: Stus-List CnC-List C&C 33 MKII Brad My race crew hates self tailers. I prefer them for thejib sheets. Hard to imagine the bearings are shot. A good clean and regrease should do it. Use oil not grease on springs and pawls. Joel 35/3 Annapolis On Saturday, February 21, 2015, Bradley Lumgair via CnC-List <[email protected]> wrote: Was at Toronto Boat Show, just realized I did pick up a catalogue for Garhauer, nice stuff as I recall. will check them out further. The plan in my little head right now is to 1) change out the halyards for all synthetic, 2) try to pull new wire from the top of the mast and rig new instruments, the old don't work anyways so I'm not losing anything even if I'm unsuccessful, 3) check bushings/trade out sheaves after the mast comes down in the fall. Theres a lot of talk about self tailing winches, aftermarket or original equipment? Eight Barient winches on ours, none are self tailing and all need servicing, I see West Marine sells springs and pawls, I should get a couple of sets for the inevitable loss, if needed I should be able to pick up bearings at a local bearing shop? Thank you for all your advise and suggestions Brad Sent, miraculously through cyberspace, from my iPad! > On Feb 21, 2015, at 04:28, [email protected] <javascript:;> > wrote: > > Send CnC-List mailing list submissions to > [email protected] <javascript:;> > > To subscribe or unsubscribe via the World Wide Web, visit > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > or, via email, send a message with subject or body 'help' to > [email protected] <javascript:;> > > You can reach the person managing the list at > [email protected] <javascript:;> > > When replying, please edit your Subject line so it is more specific > than "Re: Contents of CnC-List digest..." > Today's Topics: > > 1. Re: C&C 33 MKII (Gary Nylander) > 2. Re: C&C 33 MKII > Barient 24ST (Nauset Beach) > 3. Re: C&C 33 MKII (Marek Dziedzic) > 4. Refilling 10 lb propane tank (mike amirault) > 5. Re: Refilling 10 lb propane tank (Josh Muckley) > 6. salt water siphoning into sink (mike amirault) > 7. Re: salt water siphoning into sink (Joel Aronson) > 8. Re: salt water siphoning into sink (Mike Brannon) > 9. Re: salt water siphoning into sink (Ken Heaton) > 10. Re: salt water siphoning into sink (Jack Fitzgerald) > 11. Re: salt water siphoning into sink (Bruno Lachance) > 12. Re: salt water siphoning into sink (Graham Collins) > 13. Re: Refilling 10 lb propane tank (Graham Collins) > 14. Re: salt water siphoning into sink (Dennis C.) > 15. Re: salt water siphoning into sink (Andrew Burton) > 16. Re: salt water siphoning into sink (Russ & Melody) > 17. Re: salt water siphoning into sink (dwight veinot) > <mime-attachment> > <mime-attachment> > <mime-attachment> > <mime-attachment> > <mime-attachment> > <mime-attachment> > <mime-attachment> > <mime-attachment> > <mime-attachment> > <mime-attachment> > <mime-attachment> > <mime-attachment> > <mime-attachment> > <mime-attachment> > <mime-attachment> > <mime-attachment> > <mime-attachment> > _______________________________________________ > CnC-List mailing list > [email protected] <javascript:;> > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com _______________________________________________ Email address: [email protected] <javascript:;> To change your list preferences, including unsubscribing -- go to the bottom of page at: http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com -- Joel 301 541 8551
_______________________________________________ Email address: [email protected] To change your list preferences, including unsubscribing -- go to the bottom of page at: http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com
