So let me help out here................Joe, where are you located. I have a C&C 38MKII Hull # 125 that came with a "custom" two drop leaf teak table with a center chamber to house several liquor bottles, etc. Since we normally race this boat........the table was too heavy for our use, so I took it out and have stored it in the attic of my garage for over 12 years.
It was originally mounted on a box structure over the bilge sump that covered the Hydraulic drive turbine that drove the prop. (Long story).. That system got replaced in 2005 for a new Yanmar 3YM30 with SD20 Saildrive and we've never looked back. Depending on how you wanted to set it up, you'd need a "pedestal" mounted to your floor, or you could fashion 4 legs to make up the 12" or so in height to bring up the table to normal. That would allow you to move it if you wanted. So here's the deal. If you are near (within ???? miles) of the Boston area, it's yours, just come and pick it up. If you're farther away, you need to think about how to get it to you.........either case, it's yours. Let me know if you're interested. Ron C. Impromptu C&C 38MKIIC....'77 P.S. for you or anyone else..........I also have new (never installed) inner forestay that I was going to add to use for the smaller jibs or as a cutter rig....."Foolish thinking on my part". I also have an original C&C 38 rod forestay that came off a sister boat and didn't get used when I went to the Selden Furler...........anyone interested......just let me know. Equally reasonably priced. -----Original Message----- From: CnC-List [mailto:[email protected]] On Behalf Of Joseph Scott via CnC-List Sent: Sunday, April 19, 2015 9:09 AM To: Rick Brass Cc: [email protected] Subject: Re: Stus-List 38 Salon Table Thanks Rick. That would be wonderful. Yes I have a 38 mk2 hull #34 so I would think it would be the same as yours. The mods you did also sound great. I like what you use the lockers for too:) Thanks, Joe Sent from my iPad > On Apr 19, 2015, at 8:56 AM, Rick Brass <[email protected]> wrote: > > You didn't indicate what model of 38 you have, but if it is a 38 mk2 I would > be glad to take photos and make a dimensioned sketch for you. > > I've made a couple of modifications from the original arrangement. I found > the height of the table to be a bit lower than that of a normal table in > your home; which made access to the bilge difficult and made the fold down > leaf on the starboard side a bit of an "ankle knocker" when going forward. > So I raised the mounting on the mast a few inches and bought a longer metal > leg to support the aft end of the table. > > The port side of the table top originally was fixed, which made getting into > the port settee difficult. I modified the table top so the port side is now > a fold down leaf, similar to the starboard side. Big improvement. > > But the key feature of the table is the two storage wells in the middle of > the table top. That is now my liquor locker. > > > Rick Brass > Imzadi > C&C 38 mk2 Hull #047 > Washington, NC > > > > -----Original Message----- > From: CnC-List [mailto:[email protected]] On Behalf Of Joseph > Scott via CnC-List > Sent: Saturday, April 18, 2015 11:17 PM > To: CnClist > Subject: Stus-List 38 Salon Table > > Hello All > > When we bought our 38 it didn't have the salon table. Any ideas where I > could get a replacement or plans to make one? > > Thanks > > Joe > > Sent from my iPad > _______________________________________________ > > Email address: > [email protected] > To change your list preferences, including unsubscribing -- go to the bottom > of page at: > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > _______________________________________________ Email address: [email protected] To change your list preferences, including unsubscribing -- go to the bottom of page at: http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com _______________________________________________ Email address: [email protected] To change your list preferences, including unsubscribing -- go to the bottom of page at: http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com
