Sent you the link off list.
Neil Schiller
1970 Redwing 35, Hull #7
(C&C 35, Mark I)
"Corsair"
On 5/6/2016 12:39 PM, Brian Davis via CnC-List wrote:
Can somebody please send me that battery monitor link.
Thanks
brianwdavis...@gmail.com <mailto:brianwdavis...@gmail.com>
On May 6, 2016 7:49 AM, "schiller via CnC-List" <cnc-list@cnc-list.com
<mailto:cnc-list@cnc-list.com>> wrote:
The biggest problem on Corsair is the Main Halyard exit. The main
halyard is right above the partner with a spinnaker turning block
just forward and above that. Any wrap that I do has to split
around it. I have a couple of motorcycle inner tubes that I think
I will split and try to redo a boot. The last boot was self
fusing tape. I might try that over the inner tube after putting
some boatlife caulk around the spartite.
On another note, I finished the refrigeration installation
yesterday. I didn't document the installation like Dennis did,
but basically the same thing. Still need to add in some
additional foam under the counter top and will add some additional
foam in place around the box. Adding foam to the lid will require
a little engineering as the evaporator sits close to the lid. I
did have to trim the grate for the evaporator. Cooled the ice box
down to 37 degrees in about an hour yesterday when I fired it up.
Draws about 6 amps at start up and 5 amps running. Will have to
see what the duty cycle is as I use it. Luckily, I bought one of
the battery monitors that Joe Della Barba posted so I will be able
to count amp-hours.
Neil Schiller
1970 Redwing 35, Hull #7
(C&C 35, Mark I)
"Corsair"
soon to be in Whitehall, Mi
On 5/4/2016 4:32 AM, Dennis C. via CnC-List wrote:
I have 2 inch gray self fusing tape on Touché. Put on several
overlapping wraps. In my opinion, it's the best. Been on for
several years now and is still in good condition. Absolutely leak
tight once you fill the main sail slot with sealant like LifeSeal.
The gray blends in with the aluminum mast and collar so it's
barely noticeable. Highly recommended.
Bought it on eBay.
Dennis C.
Sent from my iPhone
On May 4, 2016, at 1:48 AM, Josh Muckley via CnC-List
<cnc-list@cnc-list.com <mailto:cnc-list@cnc-list.com>> wrote:
Ok folks,
I need a new mast boot. I've seen the poured rubber block that
is more or less permanent. Wally has a write up about how he did
it on Stella Blue and I saw it first hand on Jake's boat. I
like it but I think it is too big of a commitment right now.
Until then, I'm thinking of using the self-vulcanizing rubber
tape that is 6" wide. Having used similar products like "Rescue
Tape" for other projects, I expect that I'll need a length that
is at least 3 times the circumference of my mast collar (35" * 3
= 105").
Does anybody have any thoughts on the best way to do this job,
or which product is best?
Thanks,
Josh Muckley
S/V Sea Hawk
1989 C&C 37+
Solomons, MD
_______________________________________________
This list is supported by the generous donations of our members.
If you like what we do, please help us pay for our costs by
donating. All Contributions are greatly appreciated!
_______________________________________________
This list is supported by the generous donations of our members. If you
like what we do, please help us pay for our costs by donating. All
Contributions are greatly appreciated!
_______________________________________________
This list is supported by the generous donations of our members.
If you like what we do, please help us pay for our costs by
donating. All Contributions are greatly appreciated!
_______________________________________________
This list is supported by the generous donations of our members. If you like
what we do, please help us pay for our costs by donating. All Contributions are
greatly appreciated!
_______________________________________________
This list is supported by the generous donations of our members. If you like
what we do, please help us pay for our costs by donating. All Contributions are
greatly appreciated!
