Not happy with color Sent from my iPhone
> On Nov 19, 2017, at 2:10 PM, Fred Hazzard via CnC-List > <cnc-list@cnc-list.com> wrote: > > If you are happy with the color you have take a piece with you and your > supplier will match. > > Fred Hazzard > S/V Fury > C&C 44 > Portland Or > > Sent from my iPhone > >> On Nov 19, 2017, at 2:52 AM, Rod Stright via CnC-List >> <cnc-list@cnc-list.com> wrote: >> >> Hi Gary, >> >> Is there a name for the color of plexiglass you used? I assume it is not >> the bronze color you used? I am in the process of getting new windows for >> my C&C 99 and also like the darker color. If yu could send or post the >> pictures that would be appreciated. strig...@eastlink.ca >> >> Thanks >> Rod >> >> From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Gary >> Russell via CnC-List >> Sent: November-18-17 5:35 PM >> To: C&C List <cnc-list@cnc-list.com> >> Cc: Gary Russell <captnga...@gmail.com> >> Subject: Re: Stus-List Removing companionway slider plexiglass, C&C 37/40+ >> >> Bruce, >> There is no way of removing the acrylic without damaging the gel coat, >> so lets get that out of the way, up front. I used a router, and others have >> used sharpened putty knifes. None work very well. I've talked with the >> people at Plexus and they have no suggestions, either. I used a slightly >> darker tint of Plexiglas, and it completely hides the gel coat damage. Even >> from a few inches away, you cannot see the damage. I also like the looks of >> the darker acrylic. It's had to see in but no problem to see out. >> >> I did all the windows on Kaylarah two years ago, and installed them >> with VHB tape. I am extremely happy with the results. I have no leaks. >> Also the VHB tape is very easy to install, while the Plexus requires all >> sorts of fixtures to hold the window in place while the Plexus sets up. I >> have posted pictures many times. If you haven't seem, I can post them again. >> >> Gary >> S/V Kaylarah >> '90 C&C 37+ >> East Greenwich, RI, USA >> >> ~~~~~~~_/)~~~~~~ >> >> >> On Sat, Nov 18, 2017 at 9:16 AM, Bruce Whitmore via CnC-List >> <cnc-list@cnc-list.com> wrote: >> Hello all, >> >> I am going to replace the plexiglass on my companionway. The sliding part >> is easy. However, for the fixed portion forward of slider, it is stuck down >> to fiberglass. I am guessing that it was originally installed with Plexus >> like the fixed ports on the side were done. >> >> Can anyone confirm that? >> >> As for removing the plexi, should I simply tap a few putty knives in between >> the plexi and the fiberglass to pop it loose, or do you have a better idea? >> >> Then seal with VHB tape, correct? This area seems to be about 1 1/2" wide >> by comparison to the fixed ports. >> >> Thanks for the insights! >> >> Bruce Whitmore >> >> (847) 404-5092 (mobile) >> bwhitm...@sbcglobal.net >> >> _______________________________________________ >> >> Thanks everyone for supporting this list with your contributions. Each and >> every one is greatly appreciated. If you want to support the list - use >> PayPal to send contribution -- https://www.paypal.me/stumurray >> >> >> >> >> Virus-free. www.avast.com >> _______________________________________________ >> >> Thanks everyone for supporting this list with your contributions. Each and >> every one is greatly appreciated. If you want to support the list - use >> PayPal to send contribution -- https://www.paypal.me/stumurray >> > _______________________________________________ > > Thanks everyone for supporting this list with your contributions. Each and > every one is greatly appreciated. If you want to support the list - use > PayPal to send contribution -- https://www.paypal.me/stumurray >
_______________________________________________ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray