We have been having the exact same problems with slooow email and slow/timed out FTP connections on the virtual sites we have set up on a dedicated RAQ3 which we host at a tier one ISP. As it turns out, we did have a problem with our reverse DNS lookup (how does this happen and how do we stop it from happening again???, which the ISP recently fixed, but that did not seem to fix the problem(s). Would some kind soul please tell us how to work the web site directions below for the RAQ3? We need to have this resolved before we lose clients because of it. Thank you VERY much! << Kenn >> Kenn Krasner, Managing Partner S P H E R E S L L C U S A ____________________________________________________________________ Full service e-Business partner - access/design/maintenance/hosting/promotion Tel: 1.732.339.0700 . mailto:[EMAIL PROTECTED] . http://www.spheres.net * Named one of NJ's Top Web Development Companies by Business News NJ * Webmaster: Middlesex County Regional Chamber of Commerce * Member: NJ State Chamber of Commerce & NJ Business and Industry Ass'n * Technical Advisor: Int'l Agency for Economic Development with the UN At 03:59 PM 5/9/01 -0500, you wrote: >Thanks for the link. So, if I understand this all, the problem most likely >lies in my ISP. I tried an nslookup and it came back right away. Nameserver >stuff seems setup correctly. > >But the mail is still sluggish on sending. This is an on-again/off-again >problem. > >So, how do I follow the directions from the web site? I know I'm using >version 8.10... of sendmail. Which of the many .mc files is the one used by >a Qube 3? Is there a GUI setting I can use? > >WEB SITE DIRECTIONS: >--------------------------------------------------- >To test this (pre-8.7.y sendmail), set the IDENT timeout to zero using: > >define(`confREAD_TIMEOUT',`Ident=0')dnl > >in the .mc file used by m4 to generate your sendmail.cf file. Alternatively, >if you don't use m4, you can put ``OrIdent=0'' in the configuration file (we >recommend the m4 solution, since that makes maintenance much easier for >people who don't understand sendmail re-write rules, or after you've been >away from it for a while). Either way, this will completely disable all use >of the IDENT protocol. > >For version 8.7.y sendmail (and above), you should instead use: > >define(`confTO_IDENT',`0s')dnl >-------------------------------------------------- >So, here are what I think are the steps, but I hesitate to try it, fear of >breaking things, you know. > >1) Add "define(`confTO_IDENT',`0s')dnl" to cobalt.mc in general options area >2) "Build" >3) reboot >4) have zippy mail > >Thanks for the help! > > > -----Original Message----- > > From: [EMAIL PROTECTED] > > [mailto:[EMAIL PROTECTED]]On Behalf Of Gerald > > Waugh > > Sent: Wednesday, May 09, 2001 1:39 PM > > To: [EMAIL PROTECTED] > > Subject: Re: [cobalt-developers] slow FTP logins > > > > > > Pierre Maloka <[EMAIL PROTECTED]> wrote > > > > > > > I get the same thing on a Qube 3 with e-mail. I use > > Outlook to check my > > > email, and I get timeouts about half the time. Rather than > > use my domain > > > name, I use my local IP address, so I can't even blame the > > "Internet" for > > > this one. Any ideas? > > > > If you do nslookup ip.add.re.ss what happens? > > sendmail will still do a lookup on the ip.add.re.ss. > > Takes time for failure, then it will go ahead and > > deliver the mail anyway. > > Try sendmail FAQ at > > http://www.sendmail.org/faq/section3.html#3.12 > > Gerald > > > > > > _______________________________________________ > > cobalt-developers mailing list > > [EMAIL PROTECTED] > > http://list.cobalt.com/mailman/listinfo/cobalt-developers > > > >_______________________________________________ >cobalt-developers mailing list >[EMAIL PROTECTED] >http://list.cobalt.com/mailman/listinfo/cobalt-developers _______________________________________________ cobalt-developers mailing list [EMAIL PROTECTED] http://list.cobalt.com/mailman/listinfo/cobalt-developers
