This is an automated email from the ASF dual-hosted git repository.
simbit18 pushed a commit to branch master
in repository https://gitbox.apache.org/repos/asf/nuttx.git
The following commit(s) were added to refs/heads/master by this push:
new 4aca1700706 wireless/cc1101: Make SPI burst and single frequencies
configurable
4aca1700706 is described below
commit 4aca1700706eaead425f5cb0aeefe9e2e3e92170
Author: Chip L. <[email protected]>
AuthorDate: Thu Mar 12 16:49:47 2026 +0800
wireless/cc1101: Make SPI burst and single frequencies configurable
This patch introduces CONFIG_CC1101_SPIFREQ_BURST and
CONFIG_CC1101_SPIFREQ_SINGLE to Kconfig, allowing users to override
the default SPI frequencies for the CC1101 wireless driver.
Previously, these values were hardcoded to 6.5 MHz and 9.0 MHz
respectively. While these are safe defaults for many setups, specific
hardware designs, high routing capacitance, or platforms utilizing
internal GPIO switching matrices (such as the ESP32) can suffer from
signal integrity degradation at these speeds. By exposing these to
Kconfig, users can easily adjust the clock speeds to match their
hardware capabilities without modifying the core driver source.
Impact:
- Build: Adds two new Kconfig options under WL_CC1101.
- Runtime: Retains 6.5 MHz / 9.0 MHz defaults. Behavior only changes
if overridden via menuconfig.
Testing:
- Built with default values and custom Kconfig overrides.
- Hardware Testing: Tested on a sub-optimal platform utilizing an
internal GPIO matrix (ESP32). The CC1101 failed to load at the
default 6.5/9.0 MHz due to signal integrity issues. Downclocking
the frequencies to 4.0 MHz via Kconfig successfully restored
signal integrity and allowed the driver to initialize and operate
normally.
Signed-off-by: Chip L. <[email protected]>
---
drivers/wireless/Kconfig | 12 ++++++++++++
drivers/wireless/cc1101.c | 12 ++++++++++--
2 files changed, 22 insertions(+), 2 deletions(-)
diff --git a/drivers/wireless/Kconfig b/drivers/wireless/Kconfig
index 1eb791f7f77..c86b04f2bf0 100644
--- a/drivers/wireless/Kconfig
+++ b/drivers/wireless/Kconfig
@@ -26,6 +26,18 @@ config CC1101_SPIDEV
Selects the SPI bus number identifying that SPI interface that
connects the CC1101 to the MCU.
+config CC1101_SPIFREQ_BURST
+ int "SPI burst frequency"
+ default 6500000
+ ---help---
+ SPI burst frequency (Hz, no delay) for CC1101.
+
+config CC1101_SPIFREQ_SINGLE
+ int "SPI single access frequency"
+ default 9000000
+ ---help---
+ SPI single access frequency (Hz, single access only - no delay)
for CC1101.
+
endif
config WL_CC1101_IGNORE_VERSION
diff --git a/drivers/wireless/cc1101.c b/drivers/wireless/cc1101.c
index 8df9b5f8d22..6d27c2ecb30 100644
--- a/drivers/wireless/cc1101.c
+++ b/drivers/wireless/cc1101.c
@@ -109,8 +109,16 @@
* Pre-processor Definitions
****************************************************************************/
-#define CC1101_SPIFREQ_BURST 6500000 /* Hz, no delay */
-#define CC1101_SPIFREQ_SINGLE 9000000 /* Hz, single access only - no delay */
+#ifndef CONFIG_CC1101_SPIFREQ_BURST
+# define CONFIG_CC1101_SPIFREQ_BURST 6500000 /* Hz, no delay */
+#endif
+
+#ifndef CONFIG_CC1101_SPIFREQ_SINGLE
+# define CONFIG_CC1101_SPIFREQ_SINGLE 9000000 /* Hz, single access only -
no delay */
+#endif
+
+#define CC1101_SPIFREQ_BURST CONFIG_CC1101_SPIFREQ_BURST
+#define CC1101_SPIFREQ_SINGLE CONFIG_CC1101_SPIFREQ_SINGLE
#define CC1101_MCSM0_VALUE 0x1c
