[CONF] Apache Sling Website > OSGi Installer

[confluence]

OSGi Installer Page edited by Carsten Ziegeler Changes (1) ... If an installed bundle is managed via any other OSGi tooling, like uninstalling it through the web console, the OSGi installer does no action at all! h3. Versions and Snapshots The OSGi installer asumes that a symbolic name and version (not a snapshot version) uniquely identifies a bundle. Obviously this is a common development requirement that a released version of an artifact never changes over time. Therefore, once a bundle with a specific version is installed, it will not be reinstalled if the corresponding artifact changes. For example, if bundle A with version 1.0 is put into the JCR repository, it gets installed. If now this jar in the repository is overwritten either with the same contents or with a different one, and this new artifact has again A as the symbolic name and version set to 1.0, nothing will happen as this exact bundle is already installed. During development, SNAPSHOT versions should be used, like 1.0.0-SNAPSHOT (using the Maven convention). If a bundle with a snapshot version is changed, it gets updated by the OSGI installer. h2. Configuration Handling ... Full Content Overview The OSGi installer is a central service for handling installs, updates and uninstall of "artifacts". By default, the installer supports bundles and has an extension for handling configurations for the OSGi configuration admin. The OSGi installer itself is "just" the central service managing the tasks and states of the artifacts. The artifacts can be provided through various providers, e.g. through a file system provider reading artifacts from configured directories or the jcr provider reading artifacts from a JCR repository. A provider is just scanning for artifacts and their removal. It informs the OSGi installer about new artifacts and removed artifacts. The provider itself has usually no knowledge about the contents of an artifact. It does not know about bundles, configurations etc. As the OSGi installer itself is not performing the actual install, update or removal of an artifact, its possible to install transformers and installer factories. A transformer inspects the artifacts and tries to detect its type. By default, detecting of bundles and configurations is supported. The final service is an installer factory creating the actual task, like install this bundle, update that bundle etc. It's possible to add own providers, transformers and installer factories to support custom scenarios. Artifact Handling Once an artifact is detected by a transformer, it gets a unique id. By default a bundle gets the symbolic name and version as the unique identifier and a configuration the PID. In addition to this id, an artifact gets a priority information from the provider. The priority is used if an artifact with the same id is provided several times from different locations. For example if a file system provider is scanning two directories and an artifact with the same id (like a configuration) is added to both directories, one should have precedence over the other. This is handled by the priority. Bundle Handling In general, the OSGi installer always tries to install the highest version of a bundle if several bundles with the same symbolic name are provided. In this case higher version wins over priority. If an installed bundle is removed by a provider, for example deleted in the repository, the OSGi installer uninstall the bundle. If a bundle is removed from a provider which is currently not installed, this has no effect at all. If an installed bundle is removed and another version of this bundle is provided (a lower version), than this one is installed instead. This is basically a downgrade of the bundle. If a bundle is installed and a higher version is provided, an upgrade is performed. If an installed bundle is managed via any other OSGi tooling, like uninstalling it through the web console, the OSGi installer does no action at all! Versions and Snapshots The OSGi installer asumes that a symbolic name and version (not a snapshot version) uniquely identifies a bundle. Obviously this is a common development requirement that a released version of an artifact never changes over time. Therefore, once a bundle with a specific version is installed, it will not be reinstalled if the corresponding artifact changes. For example, if bundle A with version 1.0 is put into the JCR repository, it gets installed. If now this jar in the repository is overwritten either with the same contents or with a different one, and this new artifact has again A as the symbolic name and version set to 1.0, nothing will happen as this exact bundle is already installed. During development, SNAPSHOT versions should be used, like 1.0.0-SNAPSHOT (using the Maven convention). If a bundle with a snapshot version is changed, it gets updated by the OSGI installer. Configuration Handling In general the OSGi installer installs the configuration with the highes priority. Change Notification Preferences View Online | View Changes | Add Comment