Did you run "modprobe gadgetfs default_uid=<your uid>" before running QEMU?
I get continual kernel ring messages (dmesg, also reported in syslog) of: dummy_udc dummy_udc: dequeued req deb73c40 from ep-c, len 4096, buf xxxxxxxx Additionally, there are three lines output from QEMU's stdout/err: s3c_udc_handle_packet: EP0 overrun pcf_write: automatic Fast-charge enabled s3c_udc_handle_packet: EP0 overrun However, if I go ahead and configure the USB interface and connect via ssh, it works: ifconfig usb0 inet 192.168.0.200 netmask 255.255.255.0 ssh [EMAIL PROTECTED] - John PS: I found that the error output someone else was quoting, "Warning: could not find USB gadgetfs" near the beginning of QEMU's run is due to not having mounted /dev/gadget. Tim Niemeyer wrote: > Sent: Wednesday, July 25, 2007 6:29 AM > To: [email protected] > Subject: Re: qemu trouble... > > Hello > > I have also some problems with qemu. > I have build everything with the MokoMakefile and it works really nice! > ;-) > > But when i want to use the gadged system to ssh into my moko, i get some > trouble... > I figured out that i had to recompile my default Debian Etch Kernel an did > it. Now it seems to be all like in the wiki describes: > http://wiki.openmoko.org/wiki/OpenMoko_under_QEMU#Setting_up_USB_connectio > n > > Has anyone an idea for me? Is something wrong? > > But when i then do the "usb_add gadget:1" command the qemu repeats: > > ########################################################################## > ##### > gadget_read: event error: 4 > gadget_read: event error: 4 > gadget_read: event error: 4 > gadget_read: event error: 4 > gadget_read: event error: 4 > ########################################################################## > ##### > > > In my Syslog i can see many entrys: > > ########################################################################## > ##### > dummy_udc dummy_udc: binding gadget driver 'gadgetfs' > gadgetfs: bound to dummy_udc driver > dummy_hcd dummy_hcd: port status 0x00010101 has changes > dummy_hcd dummy_hcd: port status 0x00010101 has changes > dummy_hcd dummy_hcd: port status 0x00100503 has changes > usb 6-1: new high speed USB device using dummy_hcd and address 5 > gadgetfs: connected > gadgetfs: disconnected > dummy_hcd dummy_hcd: port status 0x00100503 has changes > dummy_udc dummy_udc: set_address = 5 > gadgetfs: connected > dummy_udc dummy_udc: enabled ep-a (ep3in-intr) maxpacket 16 > dummy_udc dummy_udc: disabled ep-a > dummy_hcd dummy_hcd: ep ep0 halted, urb e912d5c0 > dummy_udc dummy_udc: stale req = dd372840 > dummy_hcd dummy_hcd: ep ep0 halted, urb e912d5c0 > dummy_udc dummy_udc: stale req = dd372840 > dummy_hcd dummy_hcd: ep ep0 halted, urb e912d5c0 > dummy_udc dummy_udc: stale req = dd372840 > dummy_hcd dummy_hcd: ep ep0 halted, urb e912d5c0 > dummy_udc dummy_udc: stale req = dd372840 > dummy_hcd dummy_hcd: ep ep0 halted, urb e912d5c0 > dummy_udc dummy_udc: stale req = dd372840 > dummy_hcd dummy_hcd: ep ep0 halted, urb e912d5c0 > usb 6-1: string descriptor 0 read error: -32 > dummy_udc dummy_udc: stale req = dd372840 > dummy_hcd dummy_hcd: ep ep0 halted, urb e912d5c0 > dummy_udc dummy_udc: stale req = dd372840 > dummy_hcd dummy_hcd: ep ep0 halted, urb e912d5c0 > dummy_udc dummy_udc: stale req = dd372840 > dummy_hcd dummy_hcd: ep ep0 halted, urb e912d5c0 > dummy_udc dummy_udc: stale req = dd372840 > dummy_hcd dummy_hcd: ep ep0 halted, urb e912d5c0 > dummy_udc dummy_udc: stale req = dd372840 > dummy_hcd dummy_hcd: ep ep0 halted, urb e912d5c0 > dummy_udc dummy_udc: stale req = dd372840 > dummy_hcd dummy_hcd: ep ep0 halted, urb e912d5c0 > usb 6-1: string descriptor 0 read error: -32 > usb 6-1: configuration #1 chosen from 1 choice > gadgetfs: configuration #1 > ########################################################################## > ##### > > > This seems to repeat till i kill qemu and see this in my syslog: > > ########################################################################## > ##### > BUG: warning at drivers/usb/gadget/dummy_hcd.c:49 8/dummy_free_request() > [<f8cf156c>] dummy_free_request+0x41/0x4e [dummy _hcd] > [<f8cf7413>] gadgetfs_unbind+0x47/0x50 [gadgetfs ] > [<f8cf13a6>] usb_gadget_unregister_driver+0x79/0 xd2 [dummy_hcd] > [<f8cf721f>] dev_release+0x11/0x44 [gadgetfs] > [<c015ae41>] __fput+0x8a/0x13f > [<c01589aa>] filp_close+0x4e/0x54 > [<c011ead3>] put_files_struct+0x65/0xa7 > [<c011fa43>] do_exit+0x1d1/0x71b > [<c0120003>] sys_exit_group+0x0/0xd > [<c0127a6d>] get_signal_to_deliver+0x395/0x3bc > [<c01023a6>] do_notify_resume+0x71/0x5d7 > [<c0126fc1>] group_send_sig_info+0x4e/0x56 > [<c0117778>] default_wake_function+0x0/0xc > [<c0124657>] do_gettimeofday+0x31/0xce > [<c0131ffc>] sys_futex+0xdc/0xf1 > [<c0102d0a>] work_notifysig+0x13/0x19 > dummy_hcd dummy_hcd: port status 0x00010100 has c hanges > dummy_hcd dummy_hcd: port status 0x00010100 has c hanges > usb 6-1: USB disconnect, address 5 > ########################################################################## > ##### > > Thanks... > > Tim Niemeyer _______________________________________________ OpenMoko community mailing list [email protected] http://lists.openmoko.org/mailman/listinfo/community
