Hi all, I have a problem, when I setup the qemu-neo1973 envirement followed by http://wiki.openmoko.org/wiki/Qemu.
I have done these steps: sudo apt-get install netpbm lynx svn checkout https://svn.openmoko.org/trunk/src/host/qemu-neo1973 cd qemu-neo1973 ./configure --target-list=arm-softmmu --cc=/home/sunlt/gcc33 make openmoko/download.sh openmoko/flash.sh After openmoko/flash.sh, the output information is listed briefly as following(full version is an attachment): ls: /root/openmoko/qemu-neo1973/openmoko/uImage-2.6.*-neo1973.bin: No such file or directory U-Boot 1.2.0-moko9_r0 (Aug 19 2007 - 19:17:12) DRAM: 128 MB NAND: Bad block table not found for chip 0 Bad block table not found for chip 0 64 MiB *** Warning - bad CRC or NAND, using default environment Creating BBT. Please wait ...Bad block table not found for chip 0 Bad block table not found for chip 0 Bad block table written to 0x03ffc000, version 0x01 Bad block table written to 0x03ff8000, version 0x01 GTA01Bv4 # setenv bootcmd 'setenv bootargs ${bootargs_base} ${mtdparts}; bootm 0x31000000' GTA01Bv4 # setenv menu_1 'Set console to USB: setenv stdin usbtty; setenv stdout usbtty; setenv stderr usbtty' GTA01Bv4 # setenv menu_2 'Set console to serial: setenv stdin serial; setenv stdout serial; setenv stderr serial' GTA01Bv4 # setenv menu_3 'Power off: neo1973 power-off' GTA01Bv4 # setenv splashimage 'nand read.e 0x36000000 splash 0x5000; unzip 0x36000000 0x33d00000 0x96000' GTA01Bv4 # setenv mtdids nand0=neo1973-nand GTA01Bv4 # setenv mtdparts mtdparts=neo1973-nand:0x00050000(u-boot),0x00004000(u-boot_env),0x00208000(kernel),0x00010000(splash),0x039a4000(rootfs) GTA01Bv4 # #dynpart Unknown command '#dynpart' - try 'help' GTA01Bv4 # nand write.e 0x31000000 u-boot 0x33660 NAND write: device 0 offset 0x0, size 0x33660 Writing data at 0x33600 -- 100% complete. Erasing Nand...Writing to Nand... done GTA01Bv4 # neo1973 power-off poweroff pcf_write: Power-off requested. openmoko/flash.sh: line 114: 30382 已终止 ( sleep $2; kill $pid; sleep 1; kill -KILL $pid ) (wd: /root/openmoko/qemu-neo1973) Please wait, programming the NAND flash... neo_gsm_switch: GSM disabled. pcf_write: Power-off requested. Please wait, programming the NAND flash... sleep: invalid time interval 'nand' sleep: invalid time interval 'write.e' sleep: invalid time interval 'kernel' For more information, try 'sleep --help' openmoko/flash.sh: line 88: 30385 terminaled ( sleep $2; kill $pid; sleep 1; kill -KILL $pid ) openmoko/flash.sh: line 88: 30387 terminaled $qemu -mtdblock "$script_dir/$flash_base" -kernel "$script_dir/$1" -serial stdio -nographic -usb -monitor null 0<&0 U-boot failed to finish writing in nand write.e 0x31000000 kernel 0x1000 seconds, giving up. Who can help me? Thank you very much! sytax
Output-of-flash.sh
Description: Bourne shell script
_______________________________________________ OpenMoko community mailing list community@lists.openmoko.org http://lists.openmoko.org/mailman/listinfo/community