Hi, some corrections on my own mail. first off all it works now for me. second, it's not an update that causes the problem.... it is not to update... :)
the whole howto on freeyourphone.de is written for the Om2007.2/ASU-buildhost version. 2008/8/12 xaos x <[EMAIL PROTECTED]>: > > I actually finally got it working by using the article from freeyourphone > > that uses the multiplexing package. > > > > http://freeyourphone.de/portal_v1/viewtopic.php?f=21&t=295&start=0&st=0&sk=t&sd=a&sid=dda5c6cbf5850182c786488123f056ce > > > > It will receive calls and make calls while connected to GPRS using this > > setup. > > > > -Tom > it is not for an Om2008.8. the only reason why it worked for some people was, that they used the buildhost feeds again. (What is absolutly the wrong thing to do ! - But i did it too in the first time) So for them it all works fine. Now i have the correct feeds, and the howto doesn't work anymore. That is because of a different version of the gsm0710muxd application. The howto works fine also with Om2008.8. You just have to install these package before you use the howto from freeyourphone: opkg -force-depends install http://buildhost.openmoko.org/daily-feed/armv4t/gsm0710muxd_0.9.1+gitr1+3ff86b129640b647ccba3d86eb243d864671b039-r0_armv4t.ipk Attention: just use this package, and no other packages from this host! This host is normaly not compatible with the Om2008.8 !!! have a nice time with gprs until the offical gprs is comming up soon. cu all Beni P.S.: the mokoservice.py doesn't work for me. i use "gprson && gprsqison" to get into it. sometimes it doesn't work on the first time, and i have to try it a litle bit later again. Benedikt Schindler schrieb: > ok. i found out, that a upgrade from gsm0710mux is the problem. > they now have a different service name for the "muxer". > it isn't "org.pyneo.muxer" anymore it's now "org.mobile.mux". > > you could edit "/etc/X11/Xsession.d/89qtopia" so it uses the new term, > (and also the "/usr/bin/gprson" script) > or add an additional service file to /usr/share/dbus-1/system-services/ > > ---------- > > [EMAIL PROTECTED]:~# cat > /usr/share/dbus-1/system-services/org.pyneo.muxer.service > [D-BUS Service] > Name=org.pyneo.muxer > #Name=org.freesmartphone.GSM.MUX > Exec=/usr/bin/gsm0710muxd > User=root > > ----------- > > But now i have the problem that i get this errors in my log: > > Aug 16 22:26:45 om-gta02 user.notice root: Waiting for pid: 1545 > Aug 16 22:26:47 om-gta02 user.notice root: ficgta01hardware plugin > Aug 16 22:26:48 om-gta02 user.notice root: Modem : opening serial > device "/dev/ttySAC0" at 115200 > Aug 16 22:26:48 om-gta02 user.notice root: Modem : Device: > "/dev/ttySAC0" is a tty device: True > Aug 16 22:26:48 om-gta02 user.notice root: Modem : NONBLOCK > successfully reset > Aug 16 22:26:48 om-gta02 user.notice root: Modem : Opened "/dev/ttySAC0" > Aug 16 22:26:48 om-gta02 user.notice root: Modem : querying multiplexer > plugin "ficgta01multiplex" > Aug 16 22:26:48 om-gta02 user.notice root: AtChat : T : "^Z" > Aug 16 22:26:58 om-gta02 user.notice root: Mux : *** mux setup timed > out *** > Aug 16 22:26:58 om-gta02 user.notice root: AtChat : T : "^Z" > [last two lines repeat until a exit of the programm] > > > I think the "T" should be an "AT". so i try some different "gsm0710mux" > today. > maybe i found something that works. > > cu later > > [btw: answers from could have some delay, because i am on vacation and > i don't have often internet without my gprs working on the freerunner.] > > _______________________________________________ Openmoko community mailing list community@lists.openmoko.org http://lists.openmoko.org/mailman/listinfo/community