On Wed, 2009-06-10 at 23:27 -0500, Mike wrote: > I am now trying 192.168.0.202 and have no response. In fact, I get: > > ping -I usb0 192.168.0.202 > PING 192.168.0.202 (192.168.0.202) from 192.168.0.200 usb0: 56(84) bytes of > data. > From 192.168.0.200 icmp_seq=1 Destination Host Unreachable > From 192.168.0.200 icmp_seq=2 Destination Host Unreachable > From 192.168.0.200 icmp_seq=3 Destination Host Unreachable > From 192.168.0.200 icmp_seq=4 Destination Host Unreachable > From 192.168.0.200 icmp_seq=5 Destination Host Unreachable > From 192.168.0.200 icmp_seq=6 Destination Host Unreachable > ^C > --- 192.168.0.202 ping statistics --- > 9 packets transmitted, 0 received, +6 errors, 100% packet loss, time 8147ms > pipe 3 > > but > > ifconfig -a > > eth0 ... > ... > > usb0 Link encap:Ethernet HWaddr DE:D7:63:45:48:6B > inet addr:192.168.0.200 Bcast:0.0.0.0 Mask:255.255.255.0 > BROADCAST MULTICAST MTU:1500 Metric:1 > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) > > Hi Mike,
It seems your usb interface is down. the UP before broadcast is missing! >From my FR: usb0 Link encap:Ethernet HWaddr ea:83:b5:ec:59:0a inet addr:192.168.0.202 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::e883:b5ff:feec:590a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:472185 errors:0 dropped:0 overruns:0 frame:0 TX packets:645971 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:149186833 (142.2 MiB) TX bytes:840254294 (801.3 MiB) Perhaps you need to issue ifconfig usb0 up? Good luck! Ed > my firewall is off and I added "192.168.0.202 om" to /etc/hosts > > On Wednesday 10 June 2009 21:47:35 Korbinian Rosenegger wrote: > > Hi > > > > Try 192.168.0.202, the IP you tried is your desktop :) > > > > I've also done this many times until i added this line to /etc/hosts on > > my desktop: > > > > 192.168.0.202 om > > > > > > cu Korbi > > > > On Wed, 2009-06-10 at 20:17 -0500, Mike wrote: > > > Hello -- > > > > > > I just got the FR. Very nice! I am trying to SSH to FR to check the > > > firmware version. I can ping 192.168.0.200 with 0% loss. However, when I > > > > > > ssh r...@192.168.0.200 > > > > > > and enter either blank (as suggested in the Wiki) or "root" password at > > > the prompt I get "Permission denied, please try again." > > > > > > What is the problem? > > > > > > Thank you for your time, > > > > > > Mike. > > > > > > > > > > > > _______________________________________________ > > > Openmoko community mailing list > > > community@lists.openmoko.org > > > http://lists.openmoko.org/mailman/listinfo/community > > > > > _______________________________________________ > Openmoko community mailing list > community@lists.openmoko.org > http://lists.openmoko.org/mailman/listinfo/community > _______________________________________________ Openmoko community mailing list community@lists.openmoko.org http://lists.openmoko.org/mailman/listinfo/community