Ok, voici le XFConfig que j'utilise. Le pb avec Xconfigurator, c'est que
le milieu de l'�cran X est en haut (inaccessible avec la souris). C'est
comme si la taille de l'�cran X �tait deux fois plus grande que le
panneau LCD.
Olivier
--
_\\|//_
( O-O )
---------------------------------ooO-(_)-Ooo-----------------------------------
FRANCE TELECOM - CENTRE NATIONAL d'ETUDES et DES TELECOMMUNICATIONS
Dugeon olivier FT.BD/CNET/DAC/ARP
Technopole Anticipa E-mail:
[EMAIL PROTECTED]
2, Avenue Pierre Marzin Phone: +(33) 2 96 05 28 80
F-22307 LANNION Fax +(33) 2 96 05 37 84
FRANCE Telex: 740801F
--------------------------------ooO-------Ooo----------------------------------
# File generated by XConfigurator.
# **********************************************************************
# Refer to the XF86Config(4/5) man page for details about the format of
# this file.
# **********************************************************************
# **********************************************************************
# Files section. This allows default font and rgb paths to be set
# **********************************************************************
Section "Files"
RgbPath "/usr/X11R6/lib/X11/rgb"
FontPath "/usr/X11R6/lib/X11/fonts/misc/"
FontPath "/usr/X11R6/lib/X11/fonts/xtel/"
FontPath "/usr/X11R6/lib/X11/fonts/Type1/"
FontPath "/usr/X11R6/lib/X11/fonts/Speedo/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/"
EndSection
# **********************************************************************
# Server flags section.
# **********************************************************************
Section "ServerFlags"
# Uncomment this to cause a core dump at the spot where a signal is
# received. This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging
#NoTrapSignals
# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.
#DontZap
# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences. This allows clients to receive these key events.
#DontZoom
EndSection
# **********************************************************************
# Input devices
# **********************************************************************
# **********************************************************************
# Keyboard section
# **********************************************************************
Section "Keyboard"
Protocol "Standard"
#Protocol "Xqueue"
AutoRepeat 500 5
#ServerNumLock
#Xleds 1 2 3
#To set the LeftAlt to Meta, RightAlt key to ModeShift,
#RightCtl key to Compose, and ScrollLock key to ModeLock:
LeftAlt Meta
RightAlt Meta
ScrollLock Compose
RightCtl Control
# To disable the XKEYBOARD extension, uncomment XkbDisable.
# XkbDisable
XkbKeycodes "xfree86"
XkbTypes "default"
XkbCompat "default"
XkbSymbols "us(pc101)"
XkbGeometry "pc"
XkbRules "xfree86"
XkbModel "pc101"
XkbLayout "fr"
EndSection
# **********************************************************************
# Pointer section
# **********************************************************************
Section "Pointer"
# Protocol "ps/2" # PS2 mouse, Toshiba pointer
Protocol "imps/2" # Microsoft Intellimouse PS2
Device "/dev/mouse"
# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.
# Protocol "Xqueue"
# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)
Emulate3Buttons
Emulate3Timeout 50
EndSection
# **********************************************************************
# Monitor section
# **********************************************************************
# Any number of monitor sections may be present
Section "Monitor"
Identifier "Generic Multisync"
VendorName "Unknown"
ModelName "Unknown"
# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
HorizSync 25-64
# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
VertRefresh 40-70
# Modes can be specified in two formats. A compact one-line format, or
# a multi-line format.
# These two are equivalent
# ModeLine "1024x768i" 45 1024 1048 1208 1264 768 776 784 817 Interlace
# Mode "1024x768i"
# DotClock 45
# HTimings 1024 1048 1208 1264
# VTimings 768 776 784 817
# Flags "Interlace"
# EndMode
#
# Taken from Tecra720, TFT 13.3 with CT65554
#
#Modeline "800x600" 28.30 800 856 976 1040 600 637 643 666 +hsync +vsync
#Modeline "640x480" 31.50 640 680 720 864 480 488 491 521
#Modeline "320x200" 12.59 320 336 384 400 200 204 205 225 doublescan
# 1024x768 @ 60 Hz, 48.4 kHz hsync
Modeline "1024x768" 65.10 1024 1036 1240 1340 768 771 779 814 -hsync -vsync
#Modeline 60.0 or 50.0 works fine provided memclock is 50, not 44.025!!
#Modeline "1024x768" 50.0 1024 1036 1240 1340 768 771 779 814 -hsync -vsync
EndSection
# **********************************************************************
# Graphics device section
# **********************************************************************
# Any number of graphics device sections may be present
Section "Device"
Identifier "Generic VGA"
VendorName "Unknown"
BoardName "Unknown"
Chipset "generic"
# VideoRam 256
# Clocks 25.2 28.3
EndSection
# Device configured by Xconfigurator:
Section "Device"
Identifier "ViRGE/MX"
VendorName "Unknown"
BoardName "Unknown"
#VideoRam 4096
# This config works in bpp16
#Set_LCDClk 45 # 50 is too much , quake crashes
#set_mclk 40
# This config works, at -bpp 16
#Set_LCDClk 65 # 55, 50, 48, 45, 40
#set_mclk 50 #
# This config doesnt works at -bpp 24
#Set_LCDClk 50 # 60, 65, 70 crashes
#set_mclk 50 # or 40
# This config works at -bpp 24
#Set_LCDClk 40
#set_mclk 40
#option "noaccel"
# LCD screen clock
Set_LCDClk 65
#Memory clock is 44.028 Mhz in BIOS, 50Mhz max
set_mclk 50
# Turn off acceleration
#option "noaccel"
EndSection
# **********************************************************************
# Screen sections
# **********************************************************************
# The Colour SVGA server
Section "Screen"
Driver "svga"
#Device "Generic VGA"
Device "ViRGE/MX"
Monitor "Generic Multisync"
Subsection "Display"
Depth 8
Modes "1024x768" "800x600" "640x480" "320x200"
ViewPort 0 0
Virtual 1024 768
EndSubsection
Subsection "Display"
Depth 16
Modes "1024x768" "800x600" "640x480" "320x200"
ViewPort 0 0
Virtual 1024 768
EndSubsection
Subsection "Display"
Depth 24
Modes "1024x768" "800x600" "640x480" "320x200"
ViewPort 0 0
Virtual 1024 768
EndSubsection
Subsection "Display"
Depth 32
Modes "1024x768" "800x600" "640x480" "320x200"
ViewPort 0 0
Virtual 1024 768
EndSubsection
EndSection
# The 16-color VGA server
Section "Screen"
Driver "vga16"
Device "Generic VGA"
Monitor "Generic Multisync"
Subsection "Display"
Modes "640x480" "800x600"
ViewPort 0 0
Virtual 800 600
EndSubsection
EndSection
