Hi, I am back..
Good and bad news:
good: all is right t'ill scsi detection.
bad: if the onboard controller (ncr53c876) is well detected, the Smart
array is not.
So I pick it in the selection list and here is the result:
on tty5:
a message telling me that there was an error while no device for
partition found...
on tty3:
"bla, bla, bla"
"starting step 'patitionDisks'"
"no scsi avaible"
"Compaq Smart Array controller avaible"
"Error 'Une erreur est survenue pour creer de nouvelles partitions.
"Veuillez verifier votre materiel. at /usr/bin/perl-install/install2.pm
ligne 285"
on tty4
"<x> bla bla" -> detection/init of ncr53876 OK.
"<7> cpqarray: Device e11 has been found at 2 0"
"<4> Compaq SMART2 driver (v1.0.5)"
"<4> Found 1 controller(s)"
"<6> cpqarray ida/c0d0: blksz=51� nr_blks=17764320"
"<4> ida/c0d0: ida/c0d0p1 ida/c0d0p2 ida/c0d0p4"
He he, I don't ommit this...
in /proc/array, one file: ida0
"ida0: Compaq Smart Array 3200 Controller
Board ID: 40320E11
Firmware revision: 4.06
Controller Sig: a576cc28
Memory Address: 9481bf00
I/O Port: 6000
IRQ: a
Logical drives: 1
Physical drives: 1
Current Q depth: 0
Max Q depth since init: 1
Logical Drive Info:
ida/c0d0: blksiz=512 nr_blks=17764320
nr_allocs=5
nr_free=5"
in /proc/bus/pci/devices
0000 11660005 0 00000000 00000000 00000000 00000000 00000000 00000000
00000000
0030 10130000 0 C5000008 00000000 00000000 ... ... (all 0)
0078 0e110001 0 00000000 00000000 00000000 ... ... (all 0)
0088 11660005 0 00000000 00000000 00000000 ... ... (all 0)
0120 1000000f 5 00005001 c6efcf00 c6eff000 ... ... (all 0)
0121 1000000f 9 00005401 c6efce00 c6efe00 (fuck, I missed one digit...)
... ... (all 0)
0130 10680005 5 00005801 c6efd000 00000000 ... ... (all 0)
0140 10140022 0 00000000 00000000 00000000 ... ... (all 0)
0200 0e11ae10 a 00006001 c6ffff0 000000000 ... ... (all 0)
in /proc/bus/pci, 3 directory with file containing binary...
00/00.0
00/06.0
00/0f.0
00/11.0
01/04.0
01/04.1
01/06.0
01/08.0
02/00.0
That's all for panoramix...............
**********************************************************
**********************************************************
**********************************************************
NOW the old procedure (from bootnet.img): I think we have found the
miss.
Remember, on tty3:
"Found driver for NCR 53C8xx PCI"
"running /bin/insmod /bin/insmod /modules/ncr53c8xx.o"
"insmod failed!"
and same for the Smart-2/P raid controller....
There is a problem, ok, I go on tty2 and try:
# /bin/insmod /modules/cpqarray.o
/tmp/cpqarray.o: kernel-module version mismatch
/tmp/cpqarray.o was compiled for kernel version 2.2.11-BOOT
while this kernel is version 2.2.10-BOOT
#
Ye, perhaps the soluce is giving us a "bootnet.img" with kernel
2.2.11...
I would stay before my mail screen for load as soon as possible your new
version.
Thank's for your work
M. Prillot
