Axalon Bloodstone wrote:
> Yupp, (actualy i was harassing Michael ;)
>
> once again i've been caught reading email too fast..
>
> > 7.0b didn't have this problem but when I run setup then sound services
> > it detects my sound card as a Yamaha OPL3 SAX2. I then hear like one
> > second of Linus then it plays the midi w/o a problem. Now When Ever I
> > play any sound it skips. I then try Lothar and it detects the wrong
> > yamaha card. Please help me. : )
>
> I took that as what lothar detected it as.. So whats lothar say it is?
> Do you really only have 1second of audio or does the full linus quote
> play? what does conf.modules look like after it's setup with sndconfig?
>
> On Mon, 24 Jan 2000, Lyndon Lininger Sr wrote:
> > Sorry. Does this work better? I've got a Yamaha OPL3 SAx2.
> >
> > Lyndon Lininger Sr
It detects as Yamaha X Wave or something. but RH setup detects correctly.
But in both cases I get I get linus only saying "Hi" then it cuts off. Here
is what my conf.modules says:
alias eth0 3c59x
alias parport_lowlevel parport_pc
pre-install pcmcia_core /etc/rc.d/init.d/pcmcia start
alias eth1 3c59x
alias sound opl3sa2
pre-install sound /sbin/insmod sound dmabuf=1
alias midi opl3
options opl3 io=0x388
options opl3sa2 mss_io=0x530 irq=5 dma=0 dma2=1 mpu_io=0x388 io=0x370
And here is my isapnp.conf:
# $Id: pnpdump.c,v 1.20 1999/12/02 22:39:24 fox Exp $
# Release isapnptools-1.20
# This is free software, see the sources for details.
# This software has NO WARRANTY, use at your OWN RISK
#
# For details of this file format, see isapnp.conf(5)
#
# For latest information and FAQ on isapnp and pnpdump see:
# http://www.roestock.demon.co.uk/isapnptools/
#
# Compiler flags: -DREALTIME -DNEEDSETSCHEDULER -DABORT_ONRESERR
#
# Trying port address 0273
# Board 1 has serial identifier 81 ff ff ff ff 20 00 a8 65
# (DEBUG)
(READPORT 0x0273)
(ISOLATE PRESERVE)
(IDENTIFY *)
(VERBOSITY 2)
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING
# Card 1: (serial identifier 81 ff ff ff ff 20 00 a8 65)
# Vendor Id YMH0020, No Serial Number (-1), checksum 0x81.
# Version 1.0, Vendor version 0.0
# ANSI string -->OPL3-SAX Sound Board<--
#
# Logical device id YMH0021
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed
if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE YMH0020/-1 (LD 0
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0220
# IO base alignment 16 bytes
# Number of IO addresses required: 16
(IO 0 (SIZE 16) (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0530
# Maximum IO base address 0x0530
# IO base alignment 8 bytes
# Number of IO addresses required: 8
(IO 1 (SIZE 8) (BASE 0x0530))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 4 bytes
# Number of IO addresses required: 4
(IO 2 (SIZE 4) (BASE 0x0388))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0330
# Maximum IO base address 0x0330
# IO base alignment 2 bytes
# Number of IO addresses required: 2
(IO 3 (SIZE 2) (BASE 0x0330))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0370
# Maximum IO base address 0x0370
# IO base alignment 2 bytes
# Number of IO addresses required: 2
(IO 4 (SIZE 2) (BASE 0x0370))
# IRQ 5.
# High true, edge sensitive interrupt
(INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
(DMA 0 (CHANNEL 0))
# Next DMA channel 1.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
(DMA 1 (CHANNEL 1))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0240
# Maximum IO base address 0x0240
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0240))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0e80
# Maximum IO base address 0x0e80
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 1 (SIZE 8) (BASE 0x0e80))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 8 bytes
# Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0388))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0300
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 3 (SIZE 2) (BASE 0x0300))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x0ffe
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 4 (SIZE 2) (BASE 0x0100))
# IRQ 5, 7, 9, 10 or 11.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 0 (CHANNEL 0))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 1 (CHANNEL 0))
# Start dependent functions: priority functional
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0530
# Maximum IO base address 0x0f48
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 1 (SIZE 8) (BASE 0x0530))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x03f8
# IO base alignment 8 bytes
# Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0388))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0334
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 3 (SIZE 2) (BASE 0x0300))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x0ffe
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 4 (SIZE 2) (BASE 0x0100))
# IRQ 3, 5, 7, 9, 10 or 11.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 3 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 0 (CHANNEL 0))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 1 (CHANNEL 0))
# End dependent functions
(NAME "YMH0020/-1[0]{OPL3-SAX Sound Board}")
(ACT Y)
))
#
# Logical device id YMH0022
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed
if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE YMH0020/-1 (LD 1
# Compatible device id PNPb02f
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0201
# Maximum IO base address 0x0201
# IO base alignment 1 bytes
# Number of IO addresses required: 1
(IO 0 (SIZE 1) (BASE 0x0201))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0202
# Maximum IO base address 0x0202
# IO base alignment 1 bytes
# Number of IO addresses required: 1
# (IO 0 (SIZE 1) (BASE 0x0202))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0203
# Maximum IO base address 0x0203
# IO base alignment 1 bytes
# Number of IO addresses required: 1
# (IO 0 (SIZE 1) (BASE 0x0203))
# Start dependent functions: priority functional
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0204
# Maximum IO base address 0x020f
# IO base alignment 1 bytes
# Number of IO addresses required: 1
# (IO 0 (SIZE 1) (BASE 0x0204))
# End dependent functions
(NAME "YMH0020/-1[1]{OPL3-SAX Sound Board}")
(ACT Y)
))
# End tag... Checksum 0x00 (OK)
# Returns all cards to the "Wait for Key" state
(WAITFORKEY)
Thanks
Keith
