http://qa.mandrakesoft.com/show_bug.cgi?id=5229
------- Additional Comments From [EMAIL PROTECTED] 2003-05-09 20:10 -------
I ran the ptal-init setup and this is the result:
###############################################################
[EMAIL PROTECTED] root]# ptal-init setup
Stopping the HP OfficeJet Linux driver.
----------------------------------------------------------------------
This program manages devices controlled by the HP OfficeJet Linux
driver (hpoj). It attempts to probe your computer for local parallel-
and USB-connected devices, and allows you to specify network addresses
for remote JetDirect-connected devices.
If you experience any difficulties in detecting your device(s), then
refer to the hpoj documentation for troubleshooting information.
----------------------------------------------------------------------
Currently defined device names ([*]=default):
(none)
----------------------------------------------------------------------
Probe for parallel-connected devices ([y]/n)? n
----------------------------------------------------------------------
Probe for USB-connected devices ([y]/n)? y
Probing "/dev/usb/lp0"...
*** Found "psc 1200 series" but failed to communicate with it!
*** Elapsed time for this attempt was 1 second(s).
*** Check syslog file for ptal-mlcd error messages.
*** See hpoj documentation for troubleshooting information.
Probing "/dev/usb/lp1"...
No device found.
Probing "%002%001"...
No device found.
Probing "%001%001"...
No device found.
Probing "%001%002"...
No device found.
----------------------------------------------------------------------
Press <Enter> alone to continue, or if you would like to add a
JetDirect-connected device, then enter its dotted-decimal
IP address or hostname here --->
----------------------------------------------------------------------
Currently defined device names ([*]=default):
(none)
The system-wide default device name is currently set to
"mlc:usb:psc_1200_series".
Press <Enter> alone to keep this default or <Ctrl-D> to unset it,
or enter a new default device name here --->
----------------------------------------------------------------------
Done updating device configuration files stored under /etc/ptal.
If you make manual changes to those files, then be sure to run
"/usr/sbin/ptal-init start" so they will take effect.
----------------------------------------------------------------------
Starting the HP OfficeJet Linux driver.
No hpoj devices have been configured.
As root, run "/usr/sbin/ptal-init setup".
##################################################################
This output from is the syslog file:
##################################################################
Jul 5 07:38:07 ABADON scannerdrake[3045]: ### Program is starting ###
Jul 5 07:38:07 ABADON kernel: hub.c: new USB device 00:01.3-1, assigned
address 2
Jul 5 07:38:07 ABADON kernel: scanner.c: USB scanner device
(0x03f0/0x2f11) now attached to scanner0
Jul 5 07:38:07 ABADON kernel: devfs_register(lp0): could not append to
parent, err: -17
Jul 5 07:38:07 ABADON kernel: printer.c: usblp0: USB Bidirectional
printer dev 2 if 1 alt 0 proto 2 vid 0x03F0 pid 0x2F11
Jul 5 07:38:07 ABADON kernel: scanner.c: USB scanner device
(0x03f0/0x2f11) now attached to scanner1
Jul 5 07:38:08 ABADON scannerdrake[3102]: ### Program is starting ###
Jul 5 07:38:09 ABADON scannerdrake[3135]: ### Program is starting ###
Jul 5 07:38:12 ABADON /etc/hotplug/usb.agent: Setup scanner for USB
product 3f0/2f11/100
Jul 5 07:38:12 ABADON /etc/hotplug/usb.agent: Setup scanner printer for
USB product 3f0/2f11/100
Jul 5 07:38:12 ABADON /etc/hotplug/usb.agent: Setup scanner for USB
product 3f0/2f11/100
Jul 5 07:38:18 ABADON ptal-mlcd: SYSLOG at ExMgr.cpp:652,
dev=<mlc:usb:probe>, pid=3219, e=2, t=1057405098 ptal-mlcd
successfully initialized.
Jul 5 07:38:18 ABADON ptal-mlcd: SYSLOG at ExMgr.cpp:652,
dev=<mlc:usb:probe>, pid=3226, e=111, t=1057405098 ptal-mlcd
successfully initialized.
Jul 5 07:38:18 ABADON ptal-mlcd: ERROR at ExMgr.cpp:3760,
dev=<mlc:usb:probe@/dev/usb/lp0>, pid=3226, e=16, t=1057405098
Couldn't claim interface=2!
Jul 5 07:38:18 ABADON ptal-mlcd: ERROR at ExMgr.cpp:2557,
dev=<mlc:usb:probe@/dev/usb/lp0>, pid=3226, e=25, t=1057405098
Couldn't set up MLC
interface!
Jul 5 07:38:19 ABADON ptal-mlcd: SYSLOG at ExMgr.cpp:652,
dev=<mlc:usb:probe>, pid=3235, e=111, t=1057405099 ptal-mlcd
successfully initialized.
Jul 5 07:38:19 ABADON ptal-mlcd: ERROR at ExMgr.cpp:2523,
dev=<mlc:usb:probe@/dev/usb/lp1>, pid=3235, e=19, t=1057405099
Couldn't find device!
Jul 5 07:38:19 ABADON ptal-mlcd: SYSLOG at ExMgr.cpp:652,
dev=<mlc:usb:probe>, pid=3244, e=111, t=1057405099 ptal-mlcd
successfully initialized.
Jul 5 07:38:19 ABADON ptal-mlcd: ERROR at ExMgr.cpp:2523,
dev=<mlc:usb:probe>, pid=3244, e=11, t=1057405099 Couldn't find
device!
Jul 5 07:38:19 ABADON ptal-mlcd: SYSLOG at ExMgr.cpp:652,
dev=<mlc:usb:probe>, pid=3253, e=111, t=1057405099 ptal-mlcd
successfully initialized.
Jul 5 07:38:19 ABADON ptal-mlcd: ERROR at ExMgr.cpp:2523,
dev=<mlc:usb:probe>, pid=3253, e=11, t=1057405099 Couldn't find
device!
Jul 5 07:38:19 ABADON ptal-mlcd: SYSLOG at ExMgr.cpp:652,
dev=<mlc:usb:probe>, pid=3262, e=111, t=1057405099 ptal-mlcd
successfully initialized.
Jul 5 07:38:19 ABADON ptal-mlcd: ERROR at ExMgr.cpp:2523,
dev=<mlc:usb:probe>, pid=3262, e=16, t=1057405099 Couldn't find
device!
##################################################################
Thank you for you asistance and I will wait for further instructions!
Thanks
On Fri, 2003-09-05 at 13:38, [till] wrote:
--
Configure bugmail: http://qa.mandrakesoft.com/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are on the CC list for the bug, or are watching someone who is.
------- Reminder: -------
assigned_to: [EMAIL PROTECTED]
status: NEW
creation_date:
description:
I have upgraded from 9.1 and I have installed an hp 1210 usb printer. during the
installation the printer was mistakenly recognized as hp 1110. I proceeded to
correct the mistake by selecting the correct model (hp 1210), however after
sending sevelar test pages nothing happens. the following is a portion of the
messages file for your review.
Jul 2 21:54:37 ABADON devfsd[99]: error calling: "unlink" in "GLOBAL"
Jul 2 21:54:37 ABADON ptal-mlcd: SYSLOG at ExMgr.cpp:652,
dev=<mlc:usb:psc_1200_series>, pid=1630, e=2, t=1057197277 ptal-mlcd
successfully initialized.
Jul 2 21:54:38 ABADON ptal-printd: ptal-printd(mlc:usb:psc_1200_series)
successfully initialized using /var/run/ptal-printd/mlc_usb_psc_1200_series*.
Jul 2 21:54:39 ABADON insmod:
/lib/modules/2.4.22-1mdk/kernel/drivers/parport/parport_pc.o.gz: init_module:
Device or resource busy
Jul 2 21:54:39 ABADON insmod: Hint: insmod errors can be caused by incorrect
module parameters, including invalid IO or IRQ parameters. You may find
more information in syslog or the output from dmesg
Jul 2 21:54:39 ABADON modprobe: modprobe: insmod parport_lowlevel failed
Jul 2 21:54:39 ABADON kernel: lp: driver loaded but no devices found
Jul 2 21:54:42 ABADON ptal-mlcd: ERROR at ExMgr.cpp:3760,
dev=<mlc:usb:psc_1200_series@/dev/usb/lp0>, pid=1630, e=16, t=1057197282
Couldn't claim interface=2!
Jul 2 21:54:42 ABADON ptal-mlcd: ERROR at ExMgr.cpp:2557,
dev=<mlc:usb:psc_1200_series@/dev/usb/lp0>, pid=1630, e=16, t=1057197282
Couldn't set up MLC interface!
Jul 2 21:54:45 ABADON cups: cupsd startup succeeded
