http://qa.mandrakesoft.com/show_bug.cgi?id=5980
------- Additional Comments From [EMAIL PROTECTED] 2003-26-09 12:57 -------
This explains the problems I have had with the xircom network card and HP
laptop. Please fix this before releasing 9.2! I have previously talked from
this problem in the thread Xircom PCMCIA driver loading problem couple of days ago.
As I have reported in that discussion thread, I have eth0 used by the XIRCOM up
but I need to run "ifcontif eth0 ..." and "route add default gateway ..."
command by hand as a root to get everything working.
Here are my syslog and dmesg logs displaying the problem.
1) Syslog
Sep 20 17:55:34 ling2 keytable: succeeded
Sep 20 17:55:35 ling2 rc.sysinit: Enabling swap space: succeeded
Sep 20 17:55:38 ling2 mandrake_everytime: Building Window Manager Sessions succeeded
Sep 20 17:55:39 ling2 insmod:
/lib/modules/2.4.22-10mdk/kernel/drivers/pcmcia/ds.o.gz: init_module: Operation
not permitted
Sep 20 17:55:39 ling2 modprobe: modprobe: insmod eth0 failed
Sep 20 17:55:39 ling2 mandrake_everytime: Starting netprofile: succeeded
Sep 20 17:55:39 ling2 init: Entering runlevel: 5
Sep 20 17:55:39 ling2 rc: Starting switchprofile: succeeded
Sep 20 17:55:41 ling2 service_harddrake[541]: ### Program is starting ###
Sep 20 17:55:48 ling2 service_harddrake[541]: created file
/etc/sysconfig/harddrake2/previous_hw
Sep 20 17:55:48 ling2 harddrake: succeeded
Sep 20 17:55:48 ling2 network: Setting network parameters: succeeded
Sep 20 17:55:49 ling2 network: Bringing up loopback interface: succeeded
Sep 20 17:55:49 ling2 insmod:
/lib/modules/2.4.22-10mdk/kernel/drivers/pcmcia/ds.o.gz: init_module: Operation
not permitted
Sep 20 17:55:49 ling2 modprobe: modprobe: insmod eth0 failed
Sep 20 17:55:50 ling2 insmod:
/lib/modules/2.4.22-10mdk/kernel/drivers/pcmcia/ds.o.gz: init_module: Operation
not permitted
Sep 20 17:55:50 ling2 modprobe: modprobe: insmod eth0 failed
Sep 20 17:55:50 ling2 insmod:
/lib/modules/2.4.22-10mdk/kernel/drivers/pcmcia/ds.o.gz: init_module: Operation
not permitted
Sep 20 17:55:50 ling2 modprobe: modprobe: insmod eth0 failed
Sep 20 17:55:50 ling2 ifplugd(eth0)[672]: Using interface eth0
Sep 20 17:55:50 ling2 insmod:
/lib/modules/2.4.22-10mdk/kernel/drivers/pcmcia/ds.o.gz: init_module: Operation
not permitted
Sep 20 17:55:50 ling2 modprobe: modprobe: insmod eth0 failed
Sep 20 17:55:50 ling2 insmod:
/lib/modules/2.4.22-10mdk/kernel/drivers/pcmcia/ds.o.gz: init_module: Operation
not permitted
Sep 20 17:55:50 ling2 modprobe: modprobe: insmod eth0 failed
Sep 20 17:55:50 ling2 insmod:
/lib/modules/2.4.22-10mdk/kernel/drivers/pcmcia/ds.o.gz: init_module: Operation
not permitted
Sep 20 17:55:50 ling2 modprobe: modprobe: insmod eth0 failed
Sep 20 17:55:51 ling2 insmod:
/lib/modules/2.4.22-10mdk/kernel/drivers/pcmcia/ds.o.gz: init_module: Operation
not permitted
Sep 20 17:55:51 ling2 modprobe: modprobe: insmod eth0 failed
Sep 20 17:55:51 ling2 insmod:
/lib/modules/2.4.22-10mdk/kernel/drivers/pcmcia/ds.o.gz: init_module: Operation
not permitted
Sep 20 17:55:51 ling2 modprobe: modprobe: insmod eth0 failed
Sep 20 17:55:51 ling2 insmod:
/lib/modules/2.4.22-10mdk/kernel/drivers/pcmcia/ds.o.gz: init_module: Operation
not permitted
Sep 20 17:55:51 ling2 modprobe: modprobe: insmod eth0 failed
Sep 20 17:55:56 ling2 kernel: eth0: MII link partner: 0021
Sep 20 17:55:56 ling2 ifplugd(eth0)[820]: Using interface eth0/00:10:A4:E5:2E:3C
with driver <xirc2ps_cs> (version: )
Sep 20 17:55:51 ling2 insmod:
/lib/modules/2.4.22-10mdk/kernel/drivers/pcmcia/ds.o.gz: init_module: Operation
not permitted
Sep 20 17:55:57 ling2 kernel: eth0: MII selected
Sep 20 17:55:57 ling2 ifplugd(eth0)[820]: Using detection mode: SIOCDEVPRIVATE
Sep 20 17:55:51 ling2 modprobe: modprobe: insmod eth0 failed
Sep 20 17:55:57 ling2 kernel: eth0: media 10BaseT, silicon revision 4
Sep 20 17:55:57 ling2 ifplugd(eth0)[820]: ifplugd 0.15 successfully initialized,
link beat detected.
Sep 20 17:55:51 ling2 ifplugd(eth0)[672]: Failed to find working plug detection
mode for eth0
Sep 20 17:55:57 ling2 kernel: PCI: Found IRQ 10 for device 00:08.0
Sep 20 17:55:57 ling2 ifplugd(eth0)[820]: Executing '/etc/ifplugd/ifplugd.action
eth0 up'.
Sep 20 17:55:51 ling2 ifplugd(eth0)[672]: Executing '/etc/ifplugd/ifplugd.action
eth0 up'.
Sep 20 17:55:57 ling2 kernel: PCI: Sharing IRQ 10 with 00:07.2
Sep 20 17:55:52 ling2 ifplugd(eth0)[672]: client: xi
Sep 20 17:55:57 ling2 kernel: maestro: Configuring ESS Maestro 2E found at IO
0xF800 IRQ 10
Sep 20 17:55:52 ling2 ifplugd(eth0)[672]: Program execution failed, return value
is 1.
Sep 20 17:55:57 ling2 kernel: maestro: subvendor id: 0x000a103c
Sep 20 17:55:52 ling2 ifplugd(eth0)[672]: Exiting.
Sep 20 17:55:57 ling2 kernel: maestro: not attempting power management.
Sep 20 17:55:52 ling2 network: Bringing up interface eth0: failed
Sep 20 17:55:57 ling2 kernel: maestro: AC97 Codec detected: v: 0x83847609 caps:
0x6940 pwr: 0xf
Sep 20 17:55:52 ling2 internet: Checking internet connections to start at boot
succeeded
Sep 20 17:55:57 ling2 kernel: maestro: 1 channels configured.
Sep 20 17:55:52 ling2 pcmcia: Starting PCMCIA services:
Sep 20 17:55:57 ling2 kernel: maestro: version 0.15 time 12:41:37 Sep 18 2003
Sep 20 17:55:53 ling2 pcmcia: cardmgr[781]: watching 2 sockets
Sep 20 17:55:53 ling2 cardmgr[781]: watching 2 sockets
Sep 20 17:55:53 ling2 cardmgr[782]: starting, version is 3.2.4
Sep 20 17:55:53 ling2 pcmcia: done.
Sep 20 17:55:53 ling2 rc: Starting pcmcia: succeeded
Sep 20 17:55:54 ling2 cardmgr[782]: executing: 'modprobe xirc2ps_cs'
Sep 20 17:55:54 ling2 portmap: portmap startup succeeded
Sep 20 17:55:54 ling2 /etc/hotplug/net.agent: invoke ifplugd eth0
Sep 20 17:55:57 ling2 sound: Loading sound module (maestro) succeeded
Sep 20 17:55:58 ling2 random: Initializing random number generator: succeeded
Sep 20 17:55:58 ling2 xfs: xfs startup succeeded
Sep 20 17:55:59 ling2 netfs: Mounting other filesystems: succeeded
Sep 20 17:55:59 ling2 xfs: ignoring font path element
/usr/X11R6/lib/X11/fonts/drakfont (unreadable)
Sep 20 17:55:59 ling2 xfs: ignoring font path element
/usr/X11R6/lib/X11/fonts/drakfont/Type1 (unreadable)
...
2) dmesg
Linux version 2.4.22-10mdk ([EMAIL PROTECTED]) (gcc version 3.3.1
(Mandrake Linux 9.2 3.3.1-2mdk)) #1 Thu Sep 18 12:30:58 CEST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0c00 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000040e8800 (usable)
BIOS-e820: 00000000040e8800 - 00000000040efc00 (ACPI data)
BIOS-e820: 00000000040efc00 - 00000000040ffc00 (ACPI NVS)
BIOS-e820: 00000000040ffc00 - 0000000010000000 (usable)
BIOS-e820: 00000000ffff0c00 - 0000000100000000 (reserved)
256MB LOWMEM available.
ACPI: have wakeup address 0xc0001000
On node 0 totalpages: 65536
zone(0): 4096 pages.
zone(1): 61440 pages.
zone(2): 0 pages.
ACPI disabled because your bios is from 99 and too old
You can enable it with acpi=force
Building zonelist for node : 0
Kernel command line: auto BOOT_IMAGE=linux ro root=301 devfs=mount acpi=off
Local APIC disabled by BIOS -- reenabling.
Could not enable APIC!
Initializing CPU#0
Detected 497.841 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 992.87 BogoMIPS
Memory: 255500k/262144k available (1508k kernel code, 6160k reserved, -1961k
data, 156k init, 0k highmem, 0k BadRAM)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383f9ff 00000000 00000000 00000000
CPU: Common caps: 0383f9ff 00000000 00000000 00000000
CPU: Intel Pentium III (Coppermine) stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch ([EMAIL PROTECTED])
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20030813
ACPI: Interpreter disabled.
PCI: PCI BIOS revision 2.10 entry at 0xfd9cb, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: ACPI tables contain no PCI IRQ routing entries
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router PIIX [8086/7110] at 00:07.0
PCI: Found IRQ 10 for device 00:04.0
PCI: Sharing IRQ 10 with 01:00.0
PCI: Found IRQ 10 for device 00:04.1
Limiting direct PCI/PCI transfers.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Starting kswapd
kinoded started
VFS: Disk quotas vdquot_6.5.1
devfs: v1.12c (20020818) Richard Gooch ([EMAIL PROTECTED])
devfs: boot_options: 0x1
pty: 1024 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT
SHARE_IRQ SERIAL_PCI ISAPNP enabled
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 00:07.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfcf0-0xfcf7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfcf8-0xfcff, BIOS settings: hdc:DMA, hdd:pio
hda: IBM-DADA-26480, ATA DISK drive
blk: queue c0180d20, I/O limit 4095Mb (mask 0xffffffff)
hdc: _NEC CDR-2800C, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 12685680 sectors (6495 MB) w/460KiB Cache, CHS=839/240/63, UDMA(33)
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 >
ide: late registration of driver.
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Swsusp 1.0.3: Missing or invalid swap partition location (resume= parameter).
Disabled.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 89k freed
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Mounted devfs on /dev
Freeing unused kernel memory: 156k freed
Real Time Clock Driver v1.10e
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 12:42:04 Sep 18 2003
usb-uhci.c: High bandwidth mode enabled
PCI: Enabling device 00:07.2 (0000 -> 0001)
PCI: Found IRQ 10 for device 00:07.2
PCI: Sharing IRQ 10 with 00:08.0
usb-uhci.c: USB UHCI at I/O 0xfcc0, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usbdevfs: remount parameter error
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal
Adding Swap: 763520k swap-space (priority -1)
reiserfs journal head cache initialized
reiserfs: found format "3.6" with standard journal
reiserfs: using ordered data mode
reiserfs: checking transaction log (device ide0(3,5)) ...
for (ide0(3,5))
ide0(3,5):Using r5 hash to sort names
Linux Kernel Card Services Kernel Version
options: [pci] [cardbus] [pm]
ds: no socket drivers loaded!
unloading Kernel Card Services
inserting floppy driver for 2.4.22-10mdk
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
hdc: attached ide-cdrom driver.
hdc: ATAPI 24X CD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
Linux Kernel Card Services Kernel Version
options: [pci] [cardbus] [pm]
ds: no socket drivers loaded!
unloading Kernel Card Services
Linux Kernel Card Services Kernel Version
options: [pci] [cardbus] [pm]
ds: no socket drivers loaded!
unloading Kernel Card Services
Linux Kernel Card Services Kernel Version
options: [pci] [cardbus] [pm]
ds: no socket drivers loaded!
unloading Kernel Card Services
Linux Kernel Card Services Kernel Version
options: [pci] [cardbus] [pm]
ds: no socket drivers loaded!
unloading Kernel Card Services
Linux Kernel Card Services Kernel Version
options: [pci] [cardbus] [pm]
ds: no socket drivers loaded!
unloading Kernel Card Services
Linux Kernel Card Services Kernel Version
options: [pci] [cardbus] [pm]
ds: no socket drivers loaded!
unloading Kernel Card Services
Linux Kernel Card Services Kernel Version
options: [pci] [cardbus] [pm]
ds: no socket drivers loaded!
unloading Kernel Card Services
Linux Kernel Card Services Kernel Version
options: [pci] [cardbus] [pm]
ds: no socket drivers loaded!
unloading Kernel Card Services
Linux Kernel Card Services Kernel Version
options: [pci] [cardbus] [pm]
ds: no socket drivers loaded!
unloading Kernel Card Services
Linux Kernel Card Services Kernel Version
options: [pci] [cardbus] [pm]
ds: no socket drivers loaded!
unloading Kernel Card Services
Linux Kernel Card Services Kernel Version
options: [pci] [cardbus] [pm]
ds: no socket drivers loaded!
unloading Kernel Card Services
Linux Kernel Card Services Kernel Version
options: [pci] [cardbus] [pm]
PCI: Found IRQ 10 for device 00:04.0
PCI: Sharing IRQ 10 with 01:00.0
PCI: Found IRQ 10 for device 00:04.1
Yenta IRQ list 0ab8, PCI irq10
Socket status: 30000010
Yenta IRQ list 0ab8, PCI irq10
Socket status: 30000006
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
xirc2ps_cs.c 1.31 1998/12/09 19:32:55 (dd9jn+kvh)
eth0: Xircom: port 0x300, irq 3, hwaddr 00:10:A4:E5:2E:3C
eth0: MII link partner: 0021
eth0: MII selected
eth0: media 10BaseT, silicon revision 4
PCI: Found IRQ 10 for device 00:08.0
PCI: Sharing IRQ 10 with 00:07.2
maestro: Configuring ESS Maestro 2E found at IO 0xF800 IRQ 10
maestro: subvendor id: 0x000a103c
maestro: not attempting power management.
maestro: AC97 Codec detected: v: 0x83847609 caps: 0x6940 pwr: 0xf
maestro: 1 channels configured.
maestro: version 0.15 time 12:41:37 Sep 18 2003
SCSI subsystem driver Revision: 1.00
Mika
--
Configure bugmail: http://qa.mandrakesoft.com/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are on the CC list for the bug, or are watching someone who is.
------- Reminder: -------
assigned_to: [EMAIL PROTECTED]
status: UNCONFIRMED
creation_date:
description:
just a little improvement for laptop owners with pcmcia network device :
when drackconnect configure the network interface, it generate the network init
startup script before the pcmcia configuration device one. It was the same in
previous Mandrake versions. It causes the internet connection to be inactive at
startup.
Personnaly i modified the startup scripts order by hand in '/etc/rc.d/rc5.d/'
but i think it could be a small job for a good improvement (mostly for newbies).
