Hi cookers,
I quite liked GRUB, but since I got a new ATA66 disk and Promise
controller, repartitioned and used my IBM SCSI disk to boot from, it
doesn't work - all I get is the message `First stage install ...'
LILO works fine. I've tried different versions of GRUB to no avail.
Any help appreciated.
--
------------------------------------------------------
Peter Ruskin <[EMAIL PROTECTED]>
Wrexham, UK KDE - the professionals' choice
------------------------------------------------------
Linux version 2.2.16-9mdk ([EMAIL PROTECTED]) (gcc version 2.95.3 19991030
(prerelease)) #3 Sun Aug 20 14:06:46 BST 2000
Detected 399964 kHz processor.
ide_setup: ide2=0xd800,0xdc00
ide_setup: ide3=0xe000,0xe400
Console: colour VGA+ 80x25
Calibrating delay loop... 797.90 BogoMIPS
Memory: 387108k/393152k available (1236k kernel code, 420k reserved, 4252k data, 136k
init, 0k bigmem)
Dentry hash table entries: 262144 (order 9, 2048k)
Buffer cache hash table entries: 524288 (order 9, 2048k)
Page cache hash table entries: 131072 (order 7, 512k)
CPU: Intel Pentium II (Deschutes) stepping 02
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.35a (19990819) Richard Gooch ([EMAIL PROTECTED])
PCI: PCI BIOS revision 2.10 entry at 0xfb3c0
PCI: Using configuration type 1
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
TCP: Hash tables configured (ehash 524288 bhash 65536)
Initializing RT netlink socket
Starting kswapd v 1.5
matroxfb: Matrox unknown G400 (AGP) detected
matroxfb: MTRR's turned on
matroxfb: 1024x768x32bpp (virtual: 1024x4095)
matroxfb: framebuffer at 0xE8000000, mapped to 0xd8005000, size 33554432
Console: switching to colour frame buffer device 128x48
fb0: MATROX VGA frame buffer device
vga16fb: initializing
vga16fb: mapped to 0xc00a0000
fb1: VGA16 VGA frame buffer device
Detected PS/2 Mouse Port.
Serial driver version 4.27 with no serial options enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.13)
Uniform Multi-Platform E-IDE driver Revision: 6.30
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: device not capable of full native PCI mode
PIIX4: device disabled (BIOS)
PDC20262: IDE controller on PCI bus 00 dev 50
PDC20262: not 100% native mode: will probe irqs later
PDC20262: ROM enabled at 0xeb000000
PDC20262: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode.
PDC20262: FORCING PRIMARY MODE BIT 0x00 -> 0x01 MASTER
PDC20262: FORCING SECONDARY MODE BIT 0x00 -> 0x01 MASTER
ide2: BM-DMA at 0xe800-0xe807, BIOS settings: hde:DMA, hdf:pio
ide3: BM-DMA at 0xe808-0xe80f, BIOS settings: hdg:DMA, hdh:DMA
hde: probing with STATUS(0x50) instead of ALTSTATUS(0xff)
hde: Maxtor 54098U8, ATA DISK drive
hdf: probing with STATUS(0x00) instead of ALTSTATUS(0xff)
hdf: probing with STATUS(0x00) instead of ALTSTATUS(0xff)
hdg: probing with STATUS(0x50) instead of ALTSTATUS(0xff)
hdg: Maxtor 91020D6, ATA DISK drive
hdh: probing with STATUS(0x50) instead of ALTSTATUS(0xff)
hdh: Maxtor 88400D8, ATA DISK drive
ide2 at 0xd800-0xd807,0xdc00 on irq 10
ide3 at 0xe000-0xe007,0xe400 on irq 10
hde: Maxtor 54098U8, 39082MB w/2048kB Cache, CHS=79406/16/63, UDMA(66)
hdg: Maxtor 91020D6, 9728MB w/256kB Cache, CHS=19765/16/63, UDMA(33)
hdh: Maxtor 88400D8, 8011MB w/256kB Cache, CHS=16278/16/63, UDMA(33)
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
(scsi0) <Adaptec AHA-2940A Ultra SCSI host adapter> found at PCI 0/9/0
(scsi0) Narrow Channel, SCSI ID=7, 3/255 SCBs
(scsi0) Cables present (Int-50 YES, Ext-50 YES)
(scsi0) Downloading sequencer code... 422 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.31/3.2.4
<Adaptec AHA-2940A Ultra SCSI host adapter>
scsi : 1 host.
(scsi0:0:0:0) Synchronous at 10.0 Mbyte/sec, offset 15.
Vendor: IBM Model: DNES-318350 Rev: SA30
Type: Direct-Access ANSI SCSI revision: 03
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
(scsi0:0:1:0) Synchronous at 10.0 Mbyte/sec, offset 15.
Vendor: PLEXTOR Model: CD-ROM PX-32TS Rev: 1.02
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 1, lun 0
(scsi0:0:3:0) Synchronous at 10.0 Mbyte/sec, offset 15.
Vendor: YAMAHA Model: CRW8424S Rev: 1.0j
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr1 at scsi0, channel 0, id 3, lun 0
(scsi0:0:4:0) Synchronous at 10.0 Mbyte/sec, offset 8.
Vendor: PIONEER Model: DVD-ROM DVD-303 Rev: 1.09
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr2 at scsi0, channel 0, id 4, lun 0
Vendor: UMAX Model: Astra 2400S Rev: V1.1
Type: Scanner ANSI SCSI revision: 02
scsi : detected 3 SCSI cdroms 1 SCSI disk total.
Uniform CD-ROM driver Revision: 3.10
sr1: scsi3-mmc drive: 24x/16x writer cd/rw xa/form2 cdda tray
sr2: scsi3-mmc drive: 0x/0x cd/rw xa/form2 cdda tray
SCSI device sda: hdwr sector= 512 bytes. Sectors= 35843670 [17501 MB] [17.5 GB]
ne2k-pci.c:vpre-1.00e 5/27/99 D. Becker/P. Gortmaker
http://cesdis.gsfc.nasa.gov/linux/drivers/ne2k-pci.html
ne2k-pci.c: PCI NE2000 clone 'RealTek RTL-8029' at I/O 0xec00, IRQ 14.
eth0: RealTek RTL-8029 found at 0xec00, IRQ 14, 00:00:E8:D6:9B:B6.
Partition check:
sda: sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 >
hde: [PTBL] [1027/255/63] hde4 < hde5 hde6 hde7 hde8 hde9 hde10 hde11 hde12 hde13
hde14 hde15 >
hdg: [PTBL] [1027/255/63] hdg3 < hdg5 hdg6 hdg7 hdg8 hdg9 >
hdh: [PTBL] [1021/255/63] hdh1 < hdh5 >
udf: registering filesystem
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 136k freed
Adding Swap: 393552k swap-space (priority -1)
Adding Swap: 289128k swap-space (priority -2)
