Figuring cooker to be a good thing I noticed that boot disks had been
updated. So I grabbed a new cdrom boot disk and did an install. Oddly
enough after selecting partitions ( and telling the installer I had a
PS/2 mouse ) the mouse started working. ( TPA20p )
Got to the networking selection told it dhcp, but then it said it
couldn't find my ethernet card ( builtin EtherExpress Pro100 with Xircom
modem ). Rebooted and no mouse and no network... Argh!
Attached output from dmesg and lspci -vv
What happened between beta3 and RC1 that broke think pads?
-randy
Linux version 2.4.3-20mdk ([EMAIL PROTECTED]) (gcc version egcs-2.91.66
19990314/Linux (egcs-1.1.2 release / Linux-Mandrake 8.0)) #1 Sun Apr 15 23:03:10 CEST
2001
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
BIOS-e820: 000000000fff0000 - 000000000fffec00 (ACPI data)
BIOS-e820: 000000000fffec00 - 0000000010000000 (ACPI NVS)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
On node 0 totalpages: 65520
zone(0): 4096 pages.
zone(1): 61424 pages.
zone(2): 0 pages.
Kernel command line: BOOT_IMAGE=linux ro root=307
Initializing CPU#0
Detected 696.980 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1389.36 BogoMIPS
Memory: 255056k/262080k available (976k kernel code, 6636k reserved, 287k data, 696k
init, 0k highmem)
Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
VFS: Diskquotas version dquot_6.5.0 initialized
CPU: Before vendor init, caps: 0383f9ff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps: 0383f9ff 00000000 00000000 00000000
CPU: After generic, caps: 0383f9ff 00000000 00000000 00000000
CPU: Common caps: 0383f9ff 00000000 00000000 00000000
CPU: Intel Pentium III (Coppermine) stepping 03
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch ([EMAIL PROTECTED])
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfd94f, last bus=7
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Discovered primary peer bus 08 [IRQ]
PCI: Using IRQ router PIIX [8086/7110] at 00:07.0
Limiting direct PCI/PCI transfers.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.14)
Starting kswapd v1.8
pty: 256 Unix98 ptys configured
block: queued sectors max/low 169469kB/56489kB, 512 slots per queue
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1850-0x1857, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1858-0x185f, BIOS settings: hdc:DMA, hdd:pio
hda: IBM-DARA-218000, ATA DISK drive
hdc: MATSHITADVD-ROM SR-8174, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 35426160 sectors (18138 MB) w/418KiB Cache, CHS=2343/240/63, UDMA(33)
hdc: ATAPI 24X DVD-ROM drive, 512kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
Partition check:
hda: hda1 hda2 hda3 < hda5 hda6 hda7 >
Serial driver version 5.05 (2000-12-13) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ
SERIAL_PCI ISAPNP enabled
Redundant entry in serial pci_table. Please send the output of
lspci -vv, this message (4445,12,32902,9224)
and the manufacturer and name of serial board or modem board
to [EMAIL PROTECTED]
PCI: Found IRQ 11 for device 00:03.1
PCI: The same IRQ used for device 00:03.0
register_serial(): autoconfig failed
md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md.c: sizeof(mdp_super_t) = 4096
autodetecting RAID arrays
autorun ...
... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 16384)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 696k freed
Adding Swap: 355280k swap-space (priority -1)
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 203M
agpgart: Detected Intel 440BX chipset
agpgart: AGP aperture is 64M @ 0xf4000000
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.251 $ time 23:13:16 Apr 15 2001
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 11 for device 00:07.2
usb-uhci.c: USB UHCI at I/O 0x1860, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
Winbond Super-IO detection, now testing ports 3F0,370,250,4E,2E ...
SMSC Super-IO detection, now testing Ports 2F0, 370 ...
parport0: PC-style at 0x3bc [PCSPP,TRISTATE]
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
Linux PCMCIA Card Services 3.1.25
kernel build: 2.4.3-20mdk #1 Sun Apr 15 23:03:10 CEST 2001
options: [pci] [cardbus] [apm]
Intel PCIC probe: PCI: Found IRQ 11 for device 00:02.0
PCI: The same IRQ used for device 00:05.0
PCI: The same IRQ used for device 01:00.0
PCI: Found IRQ 11 for device 00:02.1
TI 1450 rev 03 PCI-to-CardBus at slot 00:02, mem 0x50000000
host opts [0]: [ring] [serial pci & irq] [pci irq 11] [lat 64/176] [bus 2/4]
host opts [1]: [ring] [serial pci & irq] [pci irq 11] [lat 64/176] [bus 5/7]
ISA irqs (scanned) = 3,4,5,7,10 PCI status changes
PCI: Found IRQ 11 for device 00:05.0
PCI: The same IRQ used for device 00:02.0
PCI: The same IRQ used for device 01:00.0
Crystal 4280/46xx + AC97 Audio, version 1.22.32, 23:13:38 Apr 15 2001
cs46xx: Card found at 0xf0122000 and 0xf0000000, IRQ 11
cs46xx: Thinkpad 600X/A20/T20 (1014:0153) at 0xf0122000/0xf0000000, IRQ 11
ac97_codec: AC97 Audio codec, id: 0x4352:0x5914 (Cirrus Logic CS4297A rev B)
Winbond Super-IO detection, now testing ports 3F0,370,250,4E,2E ...
SMSC Super-IO detection, now testing Ports 2F0, 370 ...
parport0: PC-style at 0x3bc [PCSPP,TRISTATE]
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
lp0: using parport0 (polling).
00:00.0 Host bridge: Intel Corporation 440BX/ZX - 82443BX/ZX Host bridge (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at f4000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 1.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
00:01.0 PCI bridge: Intel Corporation 440BX/ZX - 82443BX/ZX AGP bridge (rev 03)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 128
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 00002000-00002fff
Memory behind bridge: f0200000-f02fffff
Prefetchable memory behind bridge: f8000000-fbffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B+
00:02.0 CardBus bridge: Texas Instruments PCI1450 (rev 03)
Subsystem: IBM: Unknown device 0130
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64, cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 50000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=04, sec-latency=176
I/O window 0: 00000000-00000003
I/O window 1: 00000000-00000003
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:02.1 CardBus bridge: Texas Instruments PCI1450 (rev 03)
Subsystem: IBM: Unknown device 0130
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64, cache line size 08
Interrupt: pin B routed to IRQ 11
Region 0: Memory at 50100000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=05, subordinate=07, sec-latency=176
I/O window 0: 00000000-00000003
I/O window 1: 00000000-00000003
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:03.0 Ethernet controller: Intel Corporation 82557 [Ethernet Pro 100] (rev 09)
Subsystem: Intel Corporation: Unknown device 2408
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f0120000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 1800 [size=64]
Region 2: Memory at f0100000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at <unassigned> [disabled] [size=1M]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00:03.1 Serial controller: Xircom: Unknown device 000c (prog-if 02 [16550])
Subsystem: Intel Corporation: Unknown device 2408
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 1840 [size=8]
Region 1: Memory at f0121000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00:05.0 Multimedia audio controller: Cirrus Logic CS 4614/22/24 [CrystalClear
SoundFusion Audio Accelerator] (rev 01)
Subsystem: IBM: Unknown device 0153
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (1000ns min, 6000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f0122000 (32-bit, non-prefetchable) [size=4K]
Region 1: Memory at f0000000 (32-bit, non-prefetchable) [size=1M]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 Bridge: Intel Corporation 82371AB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01) (prog-if 80
[Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at 1850 [size=16]
00:07.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01) (prog-if 00
[UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at 1860 [size=32]
00:07.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 03)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
01:00.0 VGA compatible controller: ATI Technologies Inc Rage Mobility M3 AGP 2x (rev
02) (prog-if 00 [VGA])
Subsystem: IBM: Unknown device 0155
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+
SERR- FastB2B+
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 66 (2000ns min), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Region 1: I/O ports at 2000 [size=256]
Region 2: Memory at f0200000 (32-bit, non-prefetchable) [size=16K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [50] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA+ AGP- 64bit- FW- Rate=<none>
Capabilities: [5c] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
