I seem to be getting random lockups with kernel-2.4.5-9mdk that i don't get
with kernel-2.4.3-20mdk. It may be related to insmod errors on bootup during
hardware detect. It also happens most often on heavy loads.
Here is an output from dmesg on both kernels sorry about the long posts
Linux version 2.4.5-9mdk ([EMAIL PROTECTED]) (gcc version
egcs-2.91.66 19990314/Linux (egcs-1.1.2 release / Linux-Mandrake 8.1)) #1 Wed
Jun 27 18:13:14 CEST 2001
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e8c00 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000007ff0000 (usable)
BIOS-e820: 0000000007ff0000 - 0000000007fffc00 (ACPI data)
BIOS-e820: 0000000007fffc00 - 0000000008000000 (ACPI NVS)
BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
On node 0 totalpages: 32752
zone(0): 4096 pages.
zone(1): 28656 pages.
zone(2): 0 pages.
Kernel command line: BOOT_IMAGE=linux ro root=306 hdc=ide-scsi quiet
ide_setup: hdc=ide-scsi
Initializing CPU#0
Detected 856.022 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 1703.93 BogoMIPS
Memory: 125896k/131008k available (1004k kernel code, 4724k reserved, 355k
data, 700k init, 0k highmem)
Dentry-cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode-cache hash table entries: 8192 (order: 4, 65536 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
CPU: Before vendor init, caps: 0183f9ff c1c7f9ff 00000000, vendor = 2
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After vendor init, caps: 0183f9ff c1c7f9ff 00000000 00000000
CPU: After generic, caps: 0183f9ff c1c7f9ff 00000000 00000000
CPU: Common caps: 0183f9ff c1c7f9ff 00000000 00000000
CPU: AMD Athlon(tm) Processor stepping 02
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch ([EMAIL PROTECTED])
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfd80c, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
PCI: Using IRQ router VIA [1106/0686] at 00:04.0
PCI: Found IRQ 9 for device 00:04.3
PCI: The same IRQ used for device 00:04.2
PCI: Via IRQ fixup for 00:04.3, from 0 to 9
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PnP: PNP BIOS installation structure at 0xc00f8190
PnP: PNP BIOS version 1.0, entry at f0000:ac15, dseg at 400
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS not found.
Starting kswapd v1.8
VFS: Diskquotas version dquot_6.5.0 initialized
vesafb: framebuffer at 0xfc000000, mapped to 0xc8800000, size 4096k
vesafb: mode is 800x600x16, linelength=1600, pages=3
vesafb: protected mode interface info at c000:0336
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 100x37
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Serial driver version 5.05b (2001-05-03) with HUB-6 MANY_PORTS MULTIPORT
SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
block: queued sectors max/low 83578kB/27859kB, 256 slots per queue
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 21
VP_IDE: chipset revision 16
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686a (rev 22) IDE UDMA66 controller on pci00:04.1
ide0: BM-DMA at 0x10e0-0x10e7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x10e8-0x10ef, BIOS settings: hdc:pio, hdd:DMA
hda: WDC WD450AA-00BAA0, ATA DISK drive
hdc: CR-4804TE, ATAPI CD/DVD-ROM drive
hdd: SAMSUNG DVD-ROM SD-612, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 87930864 sectors (45021 MB) w/2048KiB Cache, CHS=5815/240/63, UDMA(66)
hdd: ATAPI 32X DVD-ROM drive, 512kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
Partition check:
hda: hda1 hda2 < hda5 hda6 hda7 >
md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md.c: sizeof(mdp_super_t) = 4096
autodetecting RAID arrays
autorun ...
... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 8192)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Uncompressing.......done.
Freeing initrd memory: 157k freed
VFS: Mounted root (ext2 filesystem).
SCSI subsystem driver Revision: 1.00
reiserfs: checking transaction log (device 03:06) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
VFS: Mounted root (reiserfs filesystem) readonly.
change_root: old root has d_count=2
Trying to unmount old root ... okay
Freeing unused kernel memory: 700k freed
Real Time Clock Driver v1.10d
Adding Swap: 249440k swap-space (priority -1)
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: MITSUMI Model: CR-4804TE Rev: 2.6C
Type: CD-ROM ANSI SCSI revision: 02
reiserfs: checking transaction log (device 03:07) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
MSDOS FS: Using codepage 850
MSDOS FS: IO charset iso8859-1
FAT: Did not find valid FSINFO signature.
Found signature1 0x5252 signature2 0x61416141 sector=1.
PCI: Found IRQ 11 for device 00:0d.0
PCI: The same IRQ used for device 01:05.0
3c59x.c:LK1.1.13 27 Jan 2001 Donald Becker and others.
http://www.scyld.com/network/vortex.html
See Documentation/networking/vortex.txt
eth0: 3Com PCI 3c900 Cyclone 10Mbps TPO at 0x1000, 00:10:5a:1f:c1:8a, IRQ 11
product code 504e rev 00.4 date 08-24-98
Full duplex capable
8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
MII transceiver found at address 24, status 182d.
Enabling bus-master transmits and whole-frame receives.
eth0: scatter/gather enabled. h/w checksums enabled
usb-uhci.c: $Revision: 1.259 $ time 18:24:36 Jun 27 2001
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 9 for device 00:04.2
PCI: The same IRQ used for device 00:04.3
usb-uhci.c: USB UHCI at I/O 0x10c0, IRQ 9
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 9 for device 00:04.3
PCI: The same IRQ used for device 00:04.2
usb-uhci.c: USB UHCI at I/O 0xfce0, IRQ 9
usb-uhci.c: Detected 2 ports
hub.c: USB new device connect on bus1/2, assigned device number 2
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: USB device 2 (vend/prod 0x3f0/0x405) is not claimed by any active
driver.usb-uhci.c: v1.251 Georg Acher, Deti Fliegl, Thomas Sailer, Roman
Weissgaerber
usb-uhci.c: USB Universal Host Controller Interface driver
PnPBIOS: Parport found PNPBIOS PNP0400 at io=0378,0000 irq=7 dma=-1
parport0: PC-style at 0x378, irq 7 [PCSPP,EPP]
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport_pc: Strange, can't probe Via 686A parallel port: io=0x378, irq=-1,
dma=-1
eth0: using NWAY device table, not 8
es1371: version v0.30 time 18:23:22 Jun 27 2001
PCI: Found IRQ 10 for device 00:0e.0
es1371: found chip, vendor id 0x1274 device id 0x1371 revision 0x09
es1371: found es1371 rev 9 at io 0x1080 irq 10
es1371: features: joystick 0x0
ac97_codec: AC97 Audio codec, id: 0x8384:0x7609 (SigmaTel STAC9721/23)
Linux version 2.4.3-20mdk ([EMAIL PROTECTED]) (gcc version
egcs-2.91.66 19990314/Linux (egcs-1.1.2 release / Linux-Mandrake 8.0)) #1 Sun
Apr 15 23:03:10 CEST 2001
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e8c00 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000007ff0000 (usable)
BIOS-e820: 0000000007ff0000 - 0000000007fffc00 (ACPI data)
BIOS-e820: 0000000007fffc00 - 0000000008000000 (ACPI NVS)
BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
On node 0 totalpages: 32752
zone(0): 4096 pages.
zone(1): 28656 pages.
zone(2): 0 pages.
hm, page 01000000 reserved twice.
Kernel command line: BOOT_IMAGE=old_linux ro root=306 hdc=ide-scsi quiet
ide_setup: hdc=ide-scsi
Initializing CPU#0
Detected 856.025 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 1703.93 BogoMIPS
Memory: 126008k/131008k available (976k kernel code, 4612k reserved, 287k
data, 696k init, 0k highmem)
Dentry-cache hash table entries: 16384 (order: 5, 131072 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 8192 (order: 4, 65536 bytes)
VFS: Diskquotas version dquot_6.5.0 initialized
CPU: Before vendor init, caps: 0183f9ff c1c7f9ff 00000000, vendor = 2
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After vendor init, caps: 0183f9ff c1c7f9ff 00000000 00000000
CPU: After generic, caps: 0183f9ff c1c7f9ff 00000000 00000000
CPU: Common caps: 0183f9ff c1c7f9ff 00000000 00000000
CPU: AMD Athlon(tm) Processor stepping 02
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch ([EMAIL PROTECTED])
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfd80c, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
PCI: Using IRQ router VIA [1106/0686] at 00:04.0
PCI: Found IRQ 9 for device 00:04.3
PCI: The same IRQ used for device 00:04.2
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS not found.
Starting kswapd v1.8
vesafb: framebuffer at 0xfc000000, mapped to 0xc8800000, size 4096k
vesafb: mode is 800x600x16, linelength=1600, pages=3
vesafb: protected mode interface info at c000:0336
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 100x37
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
block: queued sectors max/low 83661kB/27887kB, 256 slots per queue
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 21
VP_IDE: chipset revision 16
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686a (rev 22) IDE UDMA66 controller on pci00:04.1
ide0: BM-DMA at 0x10e0-0x10e7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x10e8-0x10ef, BIOS settings: hdc:pio, hdd:DMA
hda: WDC WD450AA-00BAA0, ATA DISK drive
hdc: CR-4804TE, ATAPI CD/DVD-ROM drive
hdd: SAMSUNG DVD-ROM SD-612, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 87930864 sectors (45021 MB) w/2048KiB Cache, CHS=5815/240/63, UDMA(33)
hdd: ATAPI 32X DVD-ROM drive, 512kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
Partition check:
hda: hda1 hda2 < hda5 hda6 hda7 >
RAMDISK: Compressed image found at block 0
Uncompressing.......done.
Freeing initrd memory: 157k freed
Serial driver version 5.05 (2000-12-13) with HUB-6 MANY_PORTS MULTIPORT
SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md.c: sizeof(mdp_super_t) = 4096
autodetecting RAID arrays
autorun ...
... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 8192)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem).
SCSI subsystem driver Revision: 1.00
reiserfs: checking transaction log (device 03:06) ...
Warning, log replay starting on readonly filesystem
reiserfs: replayed 26 transactions in 10 seconds
Using r5 hash to sort names
ReiserFS version 3.6.25
VFS: Mounted root (reiserfs filesystem) readonly.
change_root: old root has d_count=3
Trying to unmount old root ... okay
Freeing unused kernel memory: 696k freed
Real Time Clock Driver v1.10d
Adding Swap: 249440k swap-space (priority -1)
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: MITSUMI Model: CR-4804TE Rev: 2.6C
Type: CD-ROM ANSI SCSI revision: 02
reiserfs: checking transaction log (device 03:07) ...
reiserfs: replayed 16 transactions in 6 seconds
Using r5 hash to sort names
ReiserFS version 3.6.25
MSDOS FS: Using codepage 850
MSDOS FS: IO charset iso8859-1
fat_read_super: Did not find valid FSINFO signature. Found 0x61416141
PCI: Found IRQ 11 for device 00:0d.0
PCI: The same IRQ used for device 01:05.0
3c59x.c:LK1.1.13 27 Jan 2001 Donald Becker and others.
http://www.scyld.com/network/vortex.html
See Documentation/networking/vortex.txt
eth0: 3Com PCI 3c900 Cyclone 10Mbps TPO at 0x1000, 00:10:5a:1f:c1:8a, IRQ 11
product code 504e rev 00.4 date 08-24-98
Full duplex capable
8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
MII transceiver found at address 24, status 182d.
Enabling bus-master transmits and whole-frame receives.
eth0: scatter/gather enabled. h/w checksums enabled
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.251 $ time 23:13:16 Apr 15 2001
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 9 for device 00:04.2
PCI: The same IRQ used for device 00:04.3
usb-uhci.c: USB UHCI at I/O 0x10c0, IRQ 9
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 9 for device 00:04.3
PCI: The same IRQ used for device 00:04.2
usb-uhci.c: USB UHCI at I/O 0xfce0, IRQ 9
usb-uhci.c: Detected 2 ports
hub.c: USB new device connect on bus1/2, assigned device number 2
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: USB device 2 (vend/prod 0x3f0/0x405) is not claimed by any active
driver.Winbond Super-IO detection, now testing ports 3F0,370,250,4E,2E ...
SMSC Super-IO detection, now testing Ports 2F0, 370 ...
parport0: PC-style at 0x378 [PCSPP,EPP]
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport_pc: Via 686A parallel port: io=0x378
eth0: using NWAY device table, not 8
es1371: version v0.30 time 23:13:13 Apr 15 2001
es1371: found chip, vendor id 0x1274 device id 0x1371 revision 0x09
PCI: Found IRQ 10 for device 00:0e.0
es1371: found es1371 rev 9 at io 0x1080 irq 10
es1371: features: joystick 0x0
ac97_codec: AC97 Audio codec, id: 0x8384:0x7609 (SigmaTel STAC9721/23)
Undo loss 192.232.16.80/80 c2 l0 ss2/2 p0
