smth strange
/proc/mdstat
md0 : active raid0 ide/host3/bus0/target1/lun0/part6[2]
ide/host3/bus0/target0/lun0/part10[1]
ide/host2/bus0/target0/lun0/part8[0]
8064256 blocks 16k chunks
md1 : active raid0 ide/host3/bus0/target1/lun0/part7[2]
ide/host3/bus0/target0/lun0/part9[1]
ide/host2/bus0/target0/lun0/part10[0]
24579072 blocks 16k chunks
......
but i can not see VG sinn in diskdrake
and all the raids are marked as ext2
svetljo wrote:
>
>
> Pixel wrote:
>
>> svetljo <[EMAIL PROTECTED]> writes:
>>
>> [...]
>>
>>>>> could you also
>>>>> bring back " more --> reload "
>>>>>
>>>> it is there during install.
>>>>
>>> could we have it after install too
>>>
>>
>> can't you just quit and restart?
>>
> well yes , i do it, but it would be not to have to
> we had it allready , wasn't it in drakxtools 1.1.6
>
>>
>>>>> and add smth like fdisk's w " write partition table to disk "
>>>>> also under "
>>>>> more --> "
>>>>>
>>>> should not be needed. Why do you need it?
>>>>
>>> i have wrtitten to you some time ago about troubles with changing the
>>> partitions id of a raid
>>> which we had with drakxtools-1.1.5
>>> well if i change the id of /dev/md1 to LVM , done ,start again
>>> diskdrake ,
>>> it's again ext2 in case i have just created the raid or it had the
>>> id of the
>>> FS with which i had it formated some time ago
>>>
>>
>> i know this. But it was back when diskdrake wouldn't allow LVM on
>> RAID. You
>> should not need to quit diskdrake.
>>
> well but even if i add it to a VG , it remains to be marked as ext2
> when i restart diskdrake
> i 'd tryed it on a spare raid some days ago, it seems that diskdrake
> doesn't change the id on the disk( as the old one used to )
> only gives you the posibielity to add it to VG
> right now (for an hour ago) i was trying to create a PV from soft RAID-0
> but pvcreate fails with " the device is partioned " or smth similar
> i tried to recreate the RAID - raidstop , change the orther of the
> disks , mkraid
> but it still says that there are partitions on the RAID
> and i rembered me that i had that problem some months ago and
> diskdrake solve my problem
> it was the only tool, which can do this
> (have you tryed to make smth similar with fdisk, cfdisk .. on a raid)
>
>>
>>> i think it'll be the same if you change a partition from ext2 to
>>> reiserfs and
>>> do not format the partition, siply clicking done
>>> upon restart will give you the older FS
>>>
>>
>> agreed. But once again my point is that you should not need to quit
>> diskdrake!
>>
> :-) should i have diskdrake all the time running, and no reboot :-)
>
>
>>
>
>
>
[root@svetljo root]# cat /proc/lvm/global
LVM driver LVM version CVS(CVS_DATE)
Total: 3 VGs 7 PVs 4 LVs (2 LVs open 2 times)
Global: 229492 bytes malloced IOP version: 10 1:46:01 active
VG: sinn [1 PV, 0 LV/0 open] PE Size: 4096 KB
Usage [KB/PE]: 24571904 /5999 total 0 /0 used 24571904 /5999 free
PV: [AA] md/1 24571904 /5999 0 /0 24571904 /5999
LVs: none
VG: myData [3 PV, 3 LV/1 open] PE Size: 4096 KB
Usage [KB/PE]: 43515904 /10624 total 43401216 /10596 used 114688 /28 free
PVs: [AA] ide/host3/bus0/target1/lun0/part10 15183872 /3707 15183872 /3707
0 /0
[AA] md/6 14401536 /3516 14401536 /3516 0 /0
[AA] md/7 13930496 /3401 13815808 /3373 114688 /28
LVs: [AWDS3 ] Music 25165824 /6144 close
[AWDS3 ] root 6291456 /1536 1x open
[AWDL ] tmp 11943936 /2916 close
VG: wish [3 PV, 1 LV/1 open] PE Size: 4096 KB
Usage [KB/PE]: 12275712 /2997 total 11857920 /2895 used 417792 /102 free
PVs: [AA] ide/host2/bus0/target0/lun0/part7 4091904 /999 3952640 /965
139264 /34
[AA] ide/host3/bus0/target0/lun0/part8 4091904 /999 3952640 /965
139264 /34
[AA] ide/host3/bus0/target1/lun0/part5 4091904 /999 3952640 /965
139264 /34
LV: [AWDS3 ] usr 11857920 /2895 1x open
